Texas Instruments ADS794xEVM User Manual Download Page 25 | Manualshive

Page: 25 / 31

Texas Instruments ADS794xEVM User Manual Download Page 25

Revision History

25

SBAU194B – August 2011 – Revised September 2017

Submit Documentation Feedback

Copyright © 2011–2017, Texas Instruments Incorporated

Revision History

Revision History

NOTE: Page numbers for previous revisions may differ from page numbers in the current version.

Changes from A Revision (February 2016) to B Revision

.............................................................................................

Page

•

Added missing schematic diagram

....................................................................................................

Changes from Original (August 2011) to A Revision

.....................................................................................................

Page

•

Replaced reference of wall supply to external supply.

.............................................................................

•

Replaced reference of wall supply to external supply.

.............................................................................

•

Modified

Powering Up ADS794xEVM-PDK

image.

.................................................................................

«
...
23
24
25
26
27
...
»

Summary of Contents for ADS794xEVM
































Reviews:

No comments