Texas Instruments ADS7853EVM-PDK User Manual Download Page 16 | Manualshive

Page: 16 / 41

Texas Instruments ADS7853EVM-PDK User Manual Download Page 16

ADSxx53EVM-PDK Initial Setup

8.

A progress bar appears; this step takes a few minutes.

9. The progress bar is followed by an installation complete notice, as shown in

.

Figure 13. Progress Bar and Installation Complete Screens

5.2.4

Simple Capture Card Device Driver Installation

During installation of the simple capture card device driver, a prompt may appear with the Windows
security message shown in

. Select

Install this driver software anyway

to install the driver

required for proper operation of the software. The drivers contained within the installers are safe for
installation to your system.

Figure 14. Windows 7 Driver Installation Warning

NOTE:

Driver installation prompts do not appear if the simple capture card device driver has been

installed on your system previously.

16

ADS8353EVM-PDK and ADS7853EVM-PDK

SBAU210A – June 2014 – Revised August 2014

Submit Documentation Feedback

Copyright © 2014, Texas Instruments Incorporated

«
...
14
15
16
17
18
...
»

Summary of Contents for ADS7853EVM-PDK










































Reviews:

No comments