Texas Instruments ADS1x20EVM User Manual Download Page 2

Page: 2 / 24

www.ti.com

Contents

EVM Overview

...............................................................................................................

Quick Start

...................................................................................................................

Quick Reference

............................................................................................................

Using the ADS1220EVM ADCPro Plug-in

...............................................................................

ADS1220EVM Hardware Details

........................................................................................

Schematic and Bill of Materials

..........................................................................................

List of Figures

ADS1x20EVM Default Jumper Locations

................................................................................

I/O Config

....................................................................................................................

Current and Ref

.............................................................................................................

List of Tables

EVM-Compatible Device Data Sheets

...................................................................................

Default Jumper and Switch Configuration

...............................................................................

Critical Connections

........................................................................................................

Jumper and Switch Descriptions

........................................................................................

J4: Primary Analog Interface Pinout

....................................................................................

J1 and J6: Bridge Sensor Connectors

..................................................................................

J2: RTD Terminal Block Connector

.....................................................................................

J5: Auxiliary Connector

...................................................................................................

JTAG Interface Connections

.............................................................................................

JAC: External Interface Connector

......................................................................................

JDB: External Interface Connector

......................................................................................

ADS1x20EVM Bill of Materials

..........................................................................................

ADS1x20EVM

SBAU203 – July 2013

Submit Documentation Feedback

Summary of Contents for ADS1x20EVM

























Search results

Summary of Contents for ADS1x20EVM

Reviews:

Texas Instruments ADS1x20EVM, User Manual, Page: 2 / 24

Search results

Summary of Contents for ADS1x20EVM

Reviews: