background image

User’s Guide

ADC3541EVM Evaluation Module

ABSTRACT

This user’s guide describes the characteristics, operation, and use of the ADC3541 evaluation module (EVM).
This user's guide discusses how to set up and configure the software and hardware, and reviews various
aspects of the program operation. Throughout this document, the terms evaluation board, evaluation module,
and EVM are synonymous with the 

ADC3541EVM

. In the following sections of this document, the ADC3541

evaluation board is referred to as the EVM and the ADC3541 device is referred to as the ADC device.

Table of Contents

1 Introduction

.............................................................................................................................................................................

2

2 Equipment 

..............................................................................................................................................................................

2

2.1 Evaluation Board Feature Identification Summary.............................................................................................................

2

2.2 Required Equipment..........................................................................................................................................................

3

3 Setup Procedure

.....................................................................................................................................................................

4

3.1 Install High-Speed Data Converter (HSDC) Pro Software.................................................................................................

4

3.2 Install the Configuration GUI Software...............................................................................................................................

4

3.3 Connect the ADC EVM and TSW1400EVM.......................................................................................................................

4

3.4 Connect the Power Supply and Mini-USB Connections....................................................................................................

4

3.5 Connect Signal Generators to ADC3541EVM...................................................................................................................

5

3.6 Configure HSDC Pro and Capture Data............................................................................................................................

5

4 Device Configuration

..............................................................................................................................................................

7

4.1 Low Level Control..............................................................................................................................................................

7

4.2 Current Monitoring.............................................................................................................................................................

7

5 Troubleshooting

......................................................................................................................................................................

8

6 References

..............................................................................................................................................................................

8

6.1 Analog Input Configuration.................................................................................................................................................

8

List of Figures

Figure 2-1. ADC3541EVM Feature Identification........................................................................................................................

2

Figure 2-2. CMOS FPGA Interposer............................................................................................................................................

3

Figure 3-1. ADC3541EVM Full Setup..........................................................................................................................................

4

Figure 3-2. HSDC Pro: TSW1400EVM Acknowledgment...........................................................................................................

5

Figure 3-3. HSDC Pro: Data Capture..........................................................................................................................................

6

Figure 4-1. ADC35XXEVM GUI...................................................................................................................................................

7

Trademarks

Microsoft

®

 and Windows

®

 are registered trademarks of Microsoft Corporation.

All other trademarks are the property of their respective owners.

www.ti.com

Table of Contents

SBAU294 – JULY 2020

Submit Document Feedback

ADC3541EVM Evaluation Module

1

Copyright © 2020 Texas Instruments Incorporated

Summary of Contents for ADC3541EVM















Reviews: