Texas Instruments ADC1173 User Manual Download

Page: 1 / 15

SNAU224 – March 2018

Submit Documentation Feedback

ADC117x Evaluation Module

User's Guide

SNAU224 – March 2018

ADC117x Evaluation Module

This user's guide describes the function and use of the ADC117x evaluation module (EVM). Included in
this document are a quick-start guide, jumper and connector descriptions, software description, and
alternate hardware configurations.

Contents

Overview

.....................................................................................................................

Quick-Start Guide

...........................................................................................................

Evaluation Optimization

....................................................................................................

Alternate Hardware Configurations

.......................................................................................

Jumper Settings

...........................................................................................................

References

.................................................................................................................

List of Figures

EVM Feature Identification

................................................................................................

EVM Jumper Identification

..................................................................................................

Typical Test Setup Using ADC117xEVM and TSW1400EVM

.........................................................

ADC1173 Data Capture Using the HSDC Pro GUI

.....................................................................

ADC1175 Data Capture Using the HSDC Pro GUI

.....................................................................

ADC1175-50 Data Capture Using the HSDC Pro GUI

.................................................................

List of Tables

Quick-Start Measurements for ADC1173

.................................................................................

Quick-Start Measurements for ADC1175

.................................................................................

Quick-Start Measurements for ADC1175-50

.............................................................................

HSDC Pro Settings for Optimizing Results

...............................................................................

EVM Jumper Settings

......................................................................................................

Trademarks

Microsoft, Windows are registered trademarks of Microsoft Corporation.
All other trademarks are the property of their respective owners.

Summary of Contents for ADC1173
















Search results

Summary of Contents for ADC1173

Reviews:

Related manuals for ADC1173

Brands by name

Popular brands

Texas Instruments ADC1173, User Manual

Search results

Summary of Contents for ADC1173

Reviews:

Related manuals for ADC1173

Brands by name

Popular brands