23
B) Preparation
While mowing, always wear sturdy footwear
and long trousers
. Do not operate the equipment
barefoot or wearing open sandals.
Thoroughly inspect the area where the equipment
is to be used and remove all
objects which can be ejected from the machine
DANGER! Petrol is highly flammable
•
store fuel in containers specifically designed
for this purpose
•
refuel outdoors only and do not smoke while
refueling
•
add fuel before starting the engine. Never
remove the cap of the fuel tank
or add petrol while the engine is running or
when the engine is hot
•
if you spill petrol, do not start the engine and
move the machine away from the area of
spillage. Do not create any source of ignition
until the petrol vapors have evaporated
•
put back and tighten all fuel tank and
container caps securely
Replace faulty silencers
Before use
, always inspect the machine to check
that the blades, blade bolts and cutter assembly
are not worn or damaged. Replace worn or
damaged blades and bolts in sets to preserve
balance.
On multi-bladed machines, remember that the
rotation of one blade can cause
other blades to rotate
C) Operation
Do not start the engine in a confined space where
dangerous carbon monoxide fumes can collect
Mow only in daylight or good artificial light.
Before starting the engine, disengage the blades
and shift into neutral.
Do not use on slopes of more than 10° (18%)
Remember there is no such thing as a “safe”
slope
. Travelling on grass slopes requires
particular care. To guard against overturning:
•
do not stop or start suddenly when going up or
downhill
•
engage the drive slowly and always
•
keep the machine in gear, especially when
travelling downhill
▪
machine speeds should be kept low on
slopes and during tight turns
▪
stay alert for humps and hollows and
other hidden hazards
▪
never mow across the face of the
slope.
Use care when pulling loads or using heavy
equipment:
•
use only approved drawbar hitch points
•
limit loads to those you can safely control;
maximum load 200 kg
•
do not turn sharply. Use care when reversing
•
use counterweight(s) or wheel weights
whenever advised in the instruction’s manual
Disengage the blades before crossing surfaces
other than grass.
Never use the machine with damaged guards,
or without the safety protective devices in
place.
Do not change the engine governor settings or
overspeed the engine.
Operating the engine at excessive speed can
increase the risk of personal injury.
Before leaving the driving seat:
•
disengage the blades and lower the
attachments
•
go into neutral and apply the parking brake
•
stop the engine and remove the ignition key
Disengage the blades, stop the engine and
remove the ignition key:
•
before cleaning blockages or unclogging the
collector channel;
•
before cleaning, checking or servicing the
machine;
•
after striking a foreign object. Inspect the
machine for damage and make
repairs before restarting and operating the
machine;
•
If the machine starts to vibrate abnormally
(check for the causes immediately).
Disengage the blades for transport or whenever
they are not in use.
Stop the engine and disengage the blades:
•
before refueling
•
before removing the grass-catcher
Reduce the throttle during engine run-out. If the
engine is provided with a shut-off valve, cut off the
fuel when you have finished mowing
D) Maintenance an storage
Keep all nuts, bolts and screws tight to be sure the
equipment is in safe working condition.
Never store the equipment with petrol in the tank
inside a building where fumes
may reach an open flame or spark.
Allow the engine to cool before storing in any
enclosure.
To reduce fire hazards, keep the engine, silencer,
battery compartment and petrol storage area free
of grass, leaves or excessive grease.
Check the grass-catcher frequently for wear or
deterioration.
Replace worn or damaged parts for safety
purposes.
If the fuel tank has to be drained, this should be
done outdoors.
On multi-bladed machines, remember that the
rotation of one blade can cause
other blades to rotate.
When the machine is to be stored or left
unattended, lower the cutting deck
Waste electrical products (battery) must not
be disposed of with the household waste.
This tool should be taken to your local
recycling centre for safe treatment.
Summary of Contents for XC160-102HC
