background image

12

     

WARNING

The use of our products can be dangerous. Our products may only be used for their intended 

purpose. They must particularly not be used for lifting as specified in EU directive 2006/42/EC. 

The customer is responsible that the user has been trained in the safe use of the product and 

in accompanying safety precautions. Be aware of the fact that the product can cause dama-

ge if wrongly used, stored, cleaned or overloaded. Check national safety regulations, industry 

recommendations and standards for local requirements. TEUFELBERGER

®

 and 

拖飞宝

®

 are 

internationally registered trademarks of TEUFELBERGER group

.

 

   

CAUTION

This product is NOT personal protective equipment (PPE) against fall from heights!

This product accordingly does not meet the requirements of the European regulation (EU) 
2016/425 on Personal Protective Equipment (PPE) . It was however type examined by TÜV 
Austria Services GmbH, Deutschstrasse 10, A-1230 Vienna and is designed for use in work at 
height in trees (arboricultural work). 

It is important for your own safety to know and under-

stand the function of this product prior to use! 

Work at height is a high risk activity. It is your responsibility to manage those risks.
For work at height you must use suitable Personal Protective Equipment (PPE). The an-
tiSHOCK tool lanyard is NOT PPE!   

Before using this product you must:

  Inspect each component for defects;

  Read and understand all relevant User Instructions;

  Understand the scope of application of each component and any limitations;

  Recognise, register and manage the risks involved;

  Gain instruction from competent personnel where appropriate; and

  Accept that there can be no claim for damages, injury or death resulting from misuse of  

 equipment.

 CAUTION
Failure to manage risks may result in serious injury or death.

This product may be utilized only by competent persons trained in its safe use

 and 

relevantly and verifiably trained as arborists, or be under the direct supervision of such per-
sons. The antiSHOCK tool lanyard shall be allocated  to a single user: A removable label atta-
ched to the new product again warns that the antiSHOCK tool lanyard

 must not be 

mistaken 

for a lanyard of a PPE EN355 shock absorber. 
The product may be used only within the specified limited scope of use and for the defined 
purpose(s).

Prior to using this product, read this document thoroughly, make sure you understand 
the User Instructions

 and keep them for future reference.   

Edition 08/2018, art. no. 6801215

 

GENERAL

 

Summary of Contents for antiSHOCK











Reviews: