Teton Grill 720-0539 Use And Care Manual Download Page 25 | Manualshive

Page: 25 / 37

background image

TROUBLE SHOOTING

PROBLEMS

Grill won’t light when the
control knob is rotated.

CHECK LIST

WHAT TO DO

Check to see if LP tank is empty.

Clean wire(s) and /or electrode by rubbing with alcohol
and clean swab.

Wipe with dry cloth.

Make sure the wire is connected to electrode assembly.

Do other burners on the unit operate?

Check to see if other burners operate. If so, check the
gas orifice on the malfunctioning burner for an
obstruction.

Burner flame is yellow or
orange, in conjunction with
the odor of gas

Call our customer service hotline 1-800-913-8999

Low heat with knob
“IGNITE/HI” position

Is the fuel hose bent or kinked?

Is the grill in a dusty area?

Is there adequate gas supply available?

If it is only one burner that appears low, does the
orifice or burner need cleaning?

Is the gas supply, or gas pressure low?

Is the grill being preheated for 15 minutes?

25

«
...
23
24
25
26
27
...
»

Summary of Contents for 720-0539






































Reviews:

No comments

Related manuals for 720-0539

Brand: J&R Pages: 20

Brand: PALSON Pages: 28

Brand: Morsø Pages: 12

FLAME ELITE 600D3E

Brand: Z GRILLS Pages: 30

ASV 200-2B BASIC

Brand: Narex Pages: 69

OPTIGRILL GC705D16

Brand: TEFAL Pages: 112

Brand: Weber Pages: 76

Brand: Klarstein Pages: 36

Brand: TriStar Pages: 40

Brand: Kitchen Living Pages: 42

Brand: Jet Pages: 8

Brand: Thor Kitchen Pages: 27

Brand: Activa BARBECUE Pages: 6

Brand: Fisher & Paykel Pages: 2

Brand: Fisher & Paykel Pages: 21

Brand: Fisher & Paykel Pages: 52

Brand: Raider Pages: 74

Brand: Gude Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands