TESTO 440 Instruction Manual Download | Manualshive

Page: 52 / 54

background image

7 Authorisations and certification

50

Product

Mat.-No.

Date

Japan

Japan Information

USA

Contains FCC ID: N8NLSD4BTS25A
Product FCC ID: WAF-0560440X
FCC Warnings

Bluetooth SIG List

Qualified Design ID

D037513

Bluetooth radio class

Class 1

Bluetooth company

Testo SE & Co. KGaA

Bluetooth-Module

Feature

Values

Bluetooth©-range
(Newest generation of
testo climate-probes
with Bluetooth©

< 20 m (free field)

Bluetooth©-range
(Smart Probes)

< 3 m (free field)

Bluetooth© type

S25 Series BLE module , based on
TI CC2640 chip

RF Band

2402-2480MHz

Output power

5 dBm

IC Warnings

This instrument complies with Part 15B of the FCC Rules and Industry Canada RSS-210 (revision 8).
Commissioning is subject to the following two conditions:
(1) This instrument must not cause any harmful interference and
(2) this instrument must be able to cope with interference, even if this has undesirable effects on
operation.

Cet appareil satisfait à la partie 15B des directives FCC et au standard Industrie Canada RSS-210
(révision 8). Sa mise en service est soumise aux deux conditions suivantes :
(1) cet appareil ne doit causer aucune interférence dangereuse et
(2) cet appareil doit supporter toute interférence, y compris des interférences qui provoquerait des
opérations indésirables.

FCC Warnings

Information from the FCC (Federal Communications Commission)
For your own safety
Shielded cables should be used for a composite interface. This is to ensure continued protection
against radio frequency interference.

FCC warning statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or

«
...
50
51
52
53
54
»

Summary of Contents for 440























































Reviews:

No comments

Related manuals for 440

PLATINUM Series

Brand: Hach Pages: 64

Brand: Magtrol Pages: 83

Brand: QUNDIS Pages: 20

Brand: R&S Pages: 2

Brand: Valcom Pages: 1

IRmadillo DOC1048R

Brand: Keit Pages: 27

AccuPoint 2 ATP

Brand: Neogen Corporation Pages: 16

Brand: ESP Pages: 12

Brand: Solartron Mobrey Pages: 34

Brand: Axio MET Pages: 5

PRO VPR100 Series

Brand: CTC Union Pages: 10

Brand: PCB Piezotronics Pages: 15

Brand: Sercel Pages: 63

Brand: M & I Instruments Pages: 3

Brand: Teledyne Pages: 85

Brand: SICK Pages: 68

Brand: Young Pages: 5

SiteHawk SK-6000

Brand: BIRD Pages: 69

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands