background image

 

Chapter 1 – Safety 

 

 

Page 1-4 

TestEquity 3007C Temperature Chamber 

!

 

WARNING:

  The chamber door must remain closed while the chamber is operating. If you 

need to open the door while the chamber is operating, wear safety goggles to 

prevent the high velocity airflow from blowing particles or objects into your 

eyes. 

 

!

 

WARNING:

  This chamber operates at extreme temperatures. Avoid contact with air, 

objects, and surfaces that are hot or cold to prevent severe burns or frostbite. 

Protective gloves are recommended. 

 

Liquid Nitrogen (LN2) Safety Notices – applicable if LN2 is used

 

 

!

 

WARNING:  

Liquid n

itrogen is extremely cold (−190°C or −320°

F).  It can cause severe 

burns, frostbite, or eye damage. When handling liquid nitrogen containers or 

piping; wear goggles for eye protection, protective clothing, and thick 

impervious gloves (such as welder’s leather). 

 

!

 

WARNING:  

The connecting tube must include a relief valve designed for use with liquid 

nitrogen if a manual or automatic isolation valve is present at your source of 

supply or at any point between the source and the connection point on the 

back of the 3007C Chamber. This relief valve must be rated for at least 35 

psig and less than 100 psig.  It is needed to prevent excessive pressure from 

developing when the nitrogen in the connecting line evaporates during off 

cycles. Care should be exercised in sighting the relief valve to assure that 

should it relieve, the effluent will not discharge towards operating personnel. 

 

!

 

WARNING:  

All liquid nitrogen connecting piping or tubing must be well insulated with 

appropriate vapor sealed or vacuum jacketed materials. Un-insulated nitrogen 

connecting lines can condense pure oxygen on their surface since liquid 

nitrogen is colder than liquid oxygen. Liquid oxygen can present a 

spontaneous fire hazard when spilled onto organic materials. 

 

!

 

WARNING:  

Nitrogen gas is heavier than air. It makes up about 78% of the Earth’s 

standard atmosphere, is non-toxic, colorless, odorless, and tasteless. Pure 

nitrogen gas in a closed area can present an asphyxiation hazard (suffocation) 

without warning.

 

 

 

Summary of Contents for FastRate 3007C




















































Reviews:

Related manuals for FastRate 3007C