10
ENG
A (mm)
B (mm)
C (mm)
D
E
650
50 min
20 min
Air intake
Air exit
5mm
Before you install the hob, make sure that
• The work surface is square and level, and no structural members interfere with space requirements
• The work surface is made of a heat-resistant material
• If the hob is installed above an oven, the oven has a built-in cooling fan
• The installation will comply with all clearance requirements and applicable standards and regulations
• A suitable isolating switch providing full disconnection from the mains power supply is incorporated in the
permanent wiring, mounted and positioned to comply with the local wiring rules and regulations.
• The isolating switch must be of an approved type and provide a 3 mm air gap contact separation in all poles (or
in all active [phase] conductors if the local wiring rules allow for this variation of the requirements)
• The isolating switch will be easily accessible to the customer with the hob installed
• You consult local building authorities and by-laws if in doubt regarding installation
• You use heat-resistant and easy-to-clean finishes (such as ceramic tiles) for the wall surfaces surrounding the hob.
When you have installed the hob, make sure that
• The power supply cable is not accessible through cupboard doors or drawers
• There is adequate flow of fresh air from outside the cabinetry to the base of the hob
• If the hob is installed above a drawer or cupboard space, a thermal protection barrier is installed below the base
of the hob
• The isolating switch is easily accessible by the customer
Installation
Stretch out the supplied seal along the underside edge of the hob, ensuring the ends overlap.
Fig. 1
01
[04] x1
Under any circumstances, make sure the Ceramic cooker hob is well ventilated and the air inlet and outlet are not
blocked. Ensure the ceramic cooker hob is in good work state. As shown below
Note:
The safety distance between the hotplate and the cupboard above the hotplate should be at least
650 mm.
Summary of Contents for HV6410TB
