manualshive.com logo in svg

TERMOSTROJ TermoMini, Installation Manual & Users Manual, Page: 4 / 22

Share
Download
TERMOSTROJ TermoMini Installation Manual & Users Manual Download Page 4

TMS-UT-0416-T01-0 

 

Page 1 

General 

 

 

 

•

 

Keep these instructions close to the boiler! 

•

 

The boiler must not be modified, changed or rebuilt. 

•

 

The correct settings are important for economical heating. 

•

 

The type and serial number of the boiler must be quoted whenever you contact 
manufacturer or service, see the identification plate. 

 

General safety instructions!! 

 

- 

Children shall not play with the appliance.  

- 

Cleaning and user maintenance shall not be made by children without supervision.  

- 

Children should be supervised to ensure that they do not play with the appliance. 

- 

Boiler is not intended for outdoor use.  

 

Technical safety instructions!! 

 

- 

Keep the water pressure between recommended limits 

– see chapter 3.4.3, page 7. 

- 

Do not install boiler close the heat source (for instance, fireplace, wood stove etc…). 

- 

Incompetent repairs can cause serious danger to users

. 

- 

Defective parts may be replaced only by the original or approved by the 
manufacturer,

 

- 

Switch off main power by MCB before opening the boiler.

 

- 

Boiler has built-in frost protection. 

When the boiler is not in use, leave the main power 

active that protection stay active.

 

 

 

1. Introduction 

 
Thank you for the confidence you have shown to us by purchasing our central heating boiler. 
In order to use the boiler to the utmost correctly and safely, and above all economically, read 
thoroughly these instructions before continuing with installation. 
 
A competent person, who is responsible for adhering to the existing regulations, rules and 
guidelines, must install the appliances. 

1.1. Applicable documents 

The following additional documents are provided with the appliance: 
 
For the owner of the system: 
Instructions for use 
Warranty card 

For the qualified technician: 
Instructions for installation 
Electrical drawing for the appliance 

1.2. Retention of documents 

Please pass on this manual to the owner of the system. The owner should retain the 
manuals so that they are available when required. 

Read this document carefully before carrying out any installation, 

adjustment or service and follow the instructions 

Summary of Contents for TermoMini























Reviews:

No comments