background image

www.termoprodukt.com.pl 

 

 

 

A  bar  at  the  bottom  contains  information  about  the  connection  between  the  device  and 

computer.  The  middle  part  of  the  bottom  bar  shows  graphically  the  current  status  of  the 

connection with logger.  One can observe if the device is connected to the computer because 

reading of the basic data from the logger lasts during the connection. In case TERMIO-15 isn't 

connected to the computer, the bar stays still.  

 

6. Measurements

 

After switching on the programme You can see a first tab "Measurements" which contains a 

basic information about current status of the device. Information is divided into a few sections 

formed in frames. You can observe such information as: 

 

name of the logger – each Datalogger can be named to identify it, for example Freezer1, a 

Car, etc. 

 

current status (if the device is connected to the computer, if it stores the data or if it waits 

for being switched on) 

 

the clock (current time of the device) 

 

the  temperature  (current  temperature  read  from  the  device  and  information  about  set 

permissible temperature ranges of lowest and highest temperature) 

Summary of Contents for TERMIO-15



















Reviews: