background image

3.6 

Precautions for wiring work 

Warning

·  Use high-quality wiring equipment and devices, and carry out wiring 

work safely and securely according to the technical standards for 
electrical facilities, as well as the indoor wiring regulations. 

·  Only qualified personnel such as licensed electrical engineers are 

allowed to carry out electrical wiring work. 
Unqualified persons are prohibited by law from performing wiring work 
and it is very dangerous. 

·

Do not forcibly bend, pull or pinch the motor lead wire. 
Failure to observe this may result in an electric shock.

(1) 

Be sure to install a ground fault interrupter on the primary power side of the fan. 

(2) 

An overload protection device is not built into the motors with an output of over 200W. 
Separately install one. 

(3) 

Be sure to install a ground wire to prevent an electric shock. 

Do not connect the ground wire to gas pipes, water pipes, lightening arresters, or ground 
wires for telephone. 

Warning

It is prohibited by law to perform incomplete grounding work, which 
exposes personnel to a great danger. 

(4) 

The wire connection of the ALF

II 

U-20M differs between 50 Hz and 60 Hz. Connect the 

wires according to the following connection diagram. 

ALF

II

-20M circuit diagram 

Wire connection pattern

(Connection for 50 Hz)

(Connection for 60 Hz)

Black – Red 

White 

Green (Ground) 

A

u

x

ili

ary wi

ndi

ng 

Black 

White 

Red (No connection needed)

Green (Ground) 

M

a

in

 wi

ndi

ng 

Black 

White 

Red

Green

(5) 

Control the fluctuation of the voltage within ±10% of the rated voltage, and the frequency 
within ±5% of the rated frequency. If the product is not used within the range, it may break 
down. 

(6) 

Before running the fan, check the following points again: 

c

  An appropriate fuse (ground fault interrupter) is installed. 

d

  Wiring is correct. 

e

  The product is securely connected to a ground. 

f

  For three-phase power, none of the three terminals of the motor has come loose or 

is disconnected. 
Keep in mind that running with connection of only 2 terminals results in open-phase 
operation, which may cause motor burnout. 

3-3 

Summary of Contents for ALF-UII

















Reviews: