tepro CRANFORD Assembly Manual Download Page 12

10

 

 

 

Operation

 

 

Danger of combustion!

 

The BBQ contains charcoal and 
the BBQ food which is very hot, 
so any contact with the BBQ can 
cause serious burns during 
operation. 

 

Keep clear from all the hot parts, 
because any contact with the BBQ 
can cause severe burns.  

 

Wear BBQ or kitchen gloves at all 
times 

 

Only use long-handle barbecue tools 
with heat-resistant handles 

 

Do not wear clothes with loose 
sleeves  

– 

Use only dry lighter or special BBQ 
lighter (according to EN 1860-3 
guidelines) as fire lighters 

 

 

1.  Swing the grill grate (C) to the side. 

To release or fix the digits of the grill 
grate position, loosen or tighten the 
upper wing screw (S4) below the grill 
handle.

 

 

2.  The ash tray (E) catches the ashes 

during barbecuing. Do not operate 
the BBQ without the built in ash tray.  
Caution! The ash tray can be very 
hot. Do not take off the ash tray 
during barbecuing, as it heats up 
during the barbecue and is very hot.

 

 

3. 

Lay 2-3 fixed igniting material aids in 
the center of the fire bowl (A). Notice. 
Manufacturer's instructions on the 
packaging. Light the firelighters with a 
match.

 

4.  Use a maximum layer of 3 kg 

charcoal or charcoal briquettes to 
light the fire.

 

 

The BBQ must be lit for between 1 – 2 
hours before initial use.  
See section: Before BBQ.

 

 

5.  Once the charcoal is completely 

burnt, distribute the charcoal evenly 
in the fire bowl (A). For this, use a 
suitable fire resistant tool with a 
long fire resistant handle.

 

 

6.  Place the grill grate (C) over the fire 

bowl (A).

 

 

7.  Place  the  grilled  food  only  on  the 

barbecue,  when  the  charcoal  is 
covered with a light layer of ash.

 

 

8.  Barbecued food can be placed on the 

bamboo side tray (D) .

 

 

9.  Place  the  barbecued  food  on  the 

warming  wrack  (M)  to  keep  it  warm. 
The warming rack can be adjusted in 
height.  Loosen  the  wing  screw  (S4) 
with  the  square  bolt  to  adjust  the 
warming wrack in height. After setting 
the  preferred  height,  tighten  the 
thumbscrew securely.

 

 

10. On the barbecue cutlery bar (K), the 

long-stemmed and heat-resistant 
barbecue cutlery which has been 
used for barbecuing, can be hung up. 
The maximum loading of the 
barbecue cutlery bar must not exceed 
1 kg.

 

Summary of Contents for CRANFORD
















Reviews: