Tenma 72-14110 Manual Download

Page: 26 / 86

Carrier Wave Frequency Setting

Settable carrier wave frequency range is different of different carrier waveform. Default frequency of all carrier wave

is 1kHz. The frequency setting range of each carrier wave can be seen in the following table:

Carrier

Wave

Waveform

Frequency

72-14111

72-14110

Minimum

Maximum

Minimum

Maximum

Sine Wave

1μHz

10MHz

1μHz

5MHz

Square

wave

1μHz

5MHz

1μHz

5MHz

Ramp

Wave

1μHz

400kHz

1μHz

400KHz

Arbitrary

Wave

1μHz

2MHz

1μHz

1MHz

Press Parameter

→Frequency softkey in turn to set carrier wave frequency, then enter required numerical value,

and select unit.

Modulation Source Selection

This device can select internal modulation source or external modulation source. After enabling FM function, the

default of modulation source is internal. If need to change, press

1) Internal Source

When modulation source is internal, modulation wave can be: sine wave, square wave, rising ramp wave, falling

ramp wave, arbitrary wave and noise. After enabling FM function, the default of modulation wave is sine wave. If

need to change, press Carrier Wave

→Parameter→Type in turn.

Summary of Contents for 72-14110























































































Search results

Summary of Contents for 72-14110

Reviews:

Related manuals for 72-14110

Brands by name

Popular brands

Tenma 72-14110, Manual

Search results

Summary of Contents for 72-14110

Reviews:

Related manuals for 72-14110

Brands by name

Popular brands