PLATFORM GUIDE
AIRWALL™-250 SERIES
Information Security Appliance
EN
DOC-0059
PLATFORM GUIDE
Revision Date: March 2, 2020
Airwall™-250 Series
Airwall™-250 Series
Airwall™-250 Series
WIRING
Power Inputs
This device supports dual redundant power supplies, power
supply 1 (PWR 1) and power supply 2 (PWR 2). The connec-
tors for PWR 1 and PWR 2 are located on the terminal block.
Step 1: Insert the negative DC into the V- terminal and the
positive DC into the V+ terminal.
Step 2: To keep the DC wires from pulling loose, use a small
flat-blade screwdriver to tighten the wire-damp screws in the
front of the terminal block connector.
Serial Connector
Pin #
RS-232
RS-422
RS-485
(4-wire)
RS-485
(2-wire)
1
DCD
Tx-
Tx-
DATA-
2
RxD
Tx+
Tx+
DATA+
3
TxD
Rx+
Rx+
N/C
4
DTR
Rx-
Rx-
N/C
5
GND
GND
GND
GND
6
DSR
N/C
N/C
N/C
7
RTS
N/C
N/C
N/C
8
CTS
N/C
N/C
N/C
9
RI
N/C
N/C
N/C
Status LED Codes
Normal Operation On Steady
No Conductor Connection
O O O O = = O O = =
Conductor Blink
O O = =
System Error
O O O O = = O O O = =
Missing Identity
O O O = = O = =
Secure Network Error
O O O O = = =
Factory Reset
O O = = O = =
No Shared Network
O O O O = = O = =
Diagnostic Mode
O = O =
(fast blink) Downloading Firmware
O O O = = O O = =
Updating Firmware
O O O = = =
O
Blink
=
Pause
DIMENSIONS
TOP & FRONT PANEL LAYOUTS
MULTI-PURPOSE BUTTON
NOTE: Some Tempered documents may refer to this as a “Reset” button.
The multi-purpose button provides two different functions, depending on how long it is pressed and
held.
Short Tap
Press for 3 seconds and release. The Status LED will now
blink steadily.
Places the Airwall in
diagnostic mode.
Long Tap
Press for at least 8 seconds and release. The Status LED
will now blink in a 2 flash, 1 flash pattern,
Resets the Airwall to
factory defaults.
NOTE: To exit diagnostic mode, select Reboot in the diagnostic interface or turn the power of the
Airwall off and back on again.
1. LTE 2, primary antenna connector (250g/250gd)
2. LTE 1, primary antenna connector (250g/250gd)
3. LTE 1, second antenna connector (250g/250gd)
4. LTE 2, second antenna connector (250g/250gd)
5. LED: Signal indicators, LTE modems 1 & 2
6. LED: Serial port 1 activity indicator
7. LED: Serial port 2 activity indicator
8. LED: Power input 1 & 2 indicators
9. Multi-purpose button
10. LTE modem 1 microSIM card slot (250g/250gd)
11. LTE modem 2 microSIM card slot (250g/250gd)
12. Ethernet, Combo RJ-45/SFP ports
13. Ethernet ports
14. Micro-USB console port
15. Serial interface, port 1
16. Serial interface, port 2
17. Power input connector
18. Ground (earthed)
Part Number
Model
10/100/1000 Ethernet
4g Cellular Serial 802.3at/af PoE
PLF-0062-02 Airwall-250e
8
No
Yes
Yes
PLF-0066-02 Airwall-250g
8
Yes
Yes
Yes
PLF-0111-02 Airwall-250gd
8
Yes
Yes
Yes
The Airwall™-250 Series is a small form factor indus-
trial grade security appliance that facilitates private
overlay networks between customer-provided equip-
ment and devices. This document contains important
operating information, specifications, and installation
instructions.
MODELS
Safety and Warnings
Elevated Operating Ambient: If installed in a closed environment, make sure the operating ambient
temperature is compatible with the maximum ambient temperature specified by the manufacturer.
Reduced Air Flow: Make sure the amount of air flow required for safe operation of the equipment is not compro-
mised during installation.
Mechanical Loading: Make sure the mounting of the equipment is not in a hazardous condition due to uneven
mechanical loading.
Circuit Overloading: Consideration should be given to the connection of the equipment to the supply circuit and
the effect that overloading of the circuits might have on over-current protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be used when addressing this concern.
e-mail: [email protected]
Phone: +1 206.452.5500 ext. 2
www.tempered.io
19410 Hwy 99, Suite A #119
Lynnwood, WA 98036
FCC Radiation Exposure: This equipment complies with FCC radiation exposure limits set forth for
an uncontrolled environment. This equipment should be installed and operated with minimum distance
of 20cm between the radiator & your body and must not be co-located or operating in conjunction with
any other antenna or transmitter.
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his own expense.
Airwall 250g(d) contains transmitter module: FCC ID: N7NHL7588 / IC ID: 2417C-HL7588
Device Contains Approved Radio: NL-SW-LTE-S7588
CAN ICES-3 (A)/NMB-3(A)
