background image

Models ending with “N” use natural gas; models ending with “P” use propane (LP) gas.

 

TEMCO FIREPLACE PRODUCTS, Inc. 

Installation and Operating Instructions for Gas Log Heaters

 

Models 

PS24MN, PS24MP 

This appliance operates as an 

unvented room heater certified under 

ANSI Z21.11.2-2000 when fitted to a 

solid fuel burning masonry or factory 

built fireplace with the flue damper 

closed.  It also operates as a 

decorative appliance under ANSI 

Z21.60a-2000.CGA 2.26a-2000,  when 

fitted to a solid fuel burning masonry 

or factory built fireplace with the flue 

damper open.  State or local codes 

may only allow operation of this 

appliance in a vented configuration.  

GAS FIRED  
UNVENTED  
ROOM HEATERS 

LISTED 
 

 5L24 

 FOR YOUR SAFETY 

Do not store or use gasoline or other flammable vapors and liquids in the vicinity 
of this or any other appliance. 

 

WHAT TO DO IF YOU SMELL GAS  

Do not try to light any appliance. 

Do not touch any electric switch; do not use any phone in your building.  

Immediately call your gas supplier from a neighbor's phone. Follow the gas 
supplier’s instructions. 

If you cannot reach your gas supplier, call the fire department. 

 

Installation and service must be performed by a qualified installer, service agency 
or the gas supplier. 

 

If the information in this manual is not followed exactly, a fire or explosion may result 

WARNING 

This is an unvented gas-fired heater.  It uses air (oxygen) from the room in which it is 
installed.  Provisions for adequate combustion and ventilation air must be provided.  

P.O. Box 1349 Manchester, TN 37349 
 
P.O. Box 1148 Perris, CA 92572 
 
1773 Parque Industrial Cachanilla 
            Mexicali, B.C. 21600 
 
   REV.  10/30/02 10:05 AM       76780M  

PATENT NO.  US 6,390.808 B1 

Summary of Contents for PS24MN




















Reviews: