Temco ADF36-PN Installation Manual Download Page 1

TEMCO 

Vent-Free Gas Fireplaces 

Installation Manual for ADF36-ST and ADF36-PN Fireplaces 

P.O. BOX 1349 Manchester, TN 37349 

P.O. Box 1148 Perris, CA 92572 

A subsidiary of Temtex Industries, Inc.  

REV   9/9/02 10:05 AM       71875K  

See-Through Gas Fireplaces 

ADF36-ST 

Peninsula Gas Fireplaces 

ADF36-PN

 

UNIVERSALLY LISTED FOR US E WITH ANY LISTED 40,000 BTU/HR LP OR NAT GAS LOG APPLIANCE.  

 FOR YOUR SAFETY 

Do not store or use gasoline or other flammable vapors and liquids in the vicinity 
of this or any other appliance. 

Installation and service must be performed by a qualified gas installer, service 
agency or the gas supplier.  Do not attempt to install this appliance yourself! 

WHAT TO DO IF YOU SMELL GAS  

Do not light any appliance. 

Do not touch any electric switch; do not use any phone in your building.  

Immediately call your gas supplier from a neighbor's phone. Follow the gas 
supplier’s instructions. 

 

If the information in this manual is not followed exactly, a fire or explosion may result 

WARNING 

Carefully review the instructions supplied with 

the decorative type unvented room heater for the 

minimum fireplace size requirement. 

 

DO NOT INSTALL THE APPLIANCE IN THIS 

FIREBOX, UNLESS THIS FIREBOX MEETS THE 

MINIMUM DIMENSIONS REQUIRED 

FOR USE ONLY WITH 

DECORATIVE TYPE 

UNVENTED ROOM 

HEATERS 

 

 

Click here to print

Summary of Contents for ADF36-PN












Reviews: