background image

1

 

 EGT/E6291(2) KB(2) Programming Manual

 

88301 Rev 5

 

Firmware Rev 1.0.8

 

 

 

 

 

 

 

 

 

Table of Contents: 
 

Features..............................................................................................................Page 2 

 

Quick Start Guide................................................................................................Page 3 
 
Configuration Overview..................................................................................…..Page 4 
 
Manage Users.....................................................................................................Page 5 
 
Configure Lock Functions....................................................................................Page 7 
 
Configure Settings...............................................................................................Page 9 
 
Reset Options......................................................................................................Page 11 
 
Troubleshooting...................................................................................................Page 12 
 
Sample User Chart..............................................................................................Page 13 
 
User Instructions…..............................................................................................Page 14 
 

 

 
 

 

FCC Statement  

 

This device complies with Part 15 of the FCC rules. Operation is subject to the following two 
conditions: (1) This device may not cause harmful interference, and (2) this device must 
accept any interference received, including interference that may cause undesired operation. 

 

Changes or modifications not expressly approved by the party responsible for compliance 
could void the user's authority to operate the equipment.

 

Ta

bl

of

 C

on

te

nt

  

 

Summary of Contents for EGT/E6291(2) KB(2)
















Reviews: