LN930 M.2 Hardware User Guide
1VV0301078 Rev.10 – 2015-11-11
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved.
Page 87 of 88
•
Correction in Section 11.3, fixed typo in sentence: For WWAN M.2
Modules, only positions 1 and 4 are used.
•
Updated table to only indicate minimum RX sensitivity limit.
•
Updated Section Conducted Transmit Power section.
•
Added CAT 4: DL 150 Mbps, UL 50 Mbps to APAC LTE in Table 3
•
Deleted LED Blink Status in Table 14
•
Updated Table 4 and Table 27
•
Added Humidity Requirement
•
Removed Quality & Reliability section since this is a requirement of the
ODM.
•
Correction to: DPR signal includes pull-up, SSIC N/P pin locations, COEX
pin names.
8
2014-06-24
•
Added IC Canada certification wording.
•
Section 3.2.1, SIM Design Recommendations - added new section
•
Section 3.12, Antenna Interface changed connector of the WWAN antenna
cable to iPEX MHF4 from Hirose W.FLT
•
Section 7, Table 24. Operating Environment changed description for
Operating Temperature to include extreme tempe55 °C to +70 °C
and added additional description
•
Section 8.2, deleted Table 27. Electrical Parameters – Host Interface
Signals and replaced it with:
o
Table 27. DC Specification for 3.3 V Logic Signaling
o
Table 28. DC Specification for 1.8 V Logic Signaling
•
Section 8.3, Table 29. LTE Power Consumption
o
Added additional LTE Use Cases for APAC SKU only - Bands
1, 3, 8, 9, 11, 18, 19, and 21
o
Changed standby power to 8 mW
•
Section 9.6, -
o
Table 35. Rx Sensitivity – GSM - added note indicating that
GSM is not supported for APAC SKU.
o
Table 36. Rx Sensitivity – UMTS– added note indicating that
the minimum limits reflects that the main and diversity ports are
combined.
o
Table 37. Rx Sensitivity – LTE – added note indicating that the
8 LTE bands 2, 4, 5, 7, 13, 17, 20, and 26 is not supported for
APAC SKU
•
Section 9.7, Antenna Recommendations
•
Table 38. Antenna Recommendation, added note indicating that the
first 2 recommendations for Input Power are not supported for APAC
SKU.
•
Table 39. Antenna Recommendation - Bandwidth of Main &
Diversity Antenna - added not indicating that the following 9 RF
Bands 007, 010, 013, 017, 020, 025, 026, 027, and 028 are not
supported by the APAC SKU.
9
2014-11-18
•
Replaced Requirement with Target in Table 32 to Table 37.
•
Changes to Table 32. Conducted Transmit Power – 2G
•
Changes to Table 33. Conducted Transmit Power – 3G
•
Changes to Table 34. Conducted Transmit Power – LTE
•
Changes to Table 35. Rx Sensitivity – GSM
•
Changes to Table 36. Rx Sensitivity – UMTS
•
Changes to Table 37. Rx Sensitivity – LTE
•
Changes to Table 38. Antenna Recommendation
10
2014-12-21
•
Added note to Table 3. WWAN M.2 Module – Data Services
•
− The change is to describe we can support DL 150 Mbps in WW LTE
SKU. This is only for generic SW and VZW SW, but not for AT&T SW.
•
Changes to Section 3.2 USIM Interface
•
− Bullet number 2 and 3
•
Changes to Section 3.2 USIM Interface
List number 2 and 3
•
Changes to Table 4. WWAN M.2 Host Interface Signals pins 29, 31, 35,
and 37.
•
Changes to Table 6. USB SSIC - ICP Interface
•
Changes to Table 33. Conducted Transmit Power – LTE
•
Changes to Table 4. WWAN M.2 Host Interface Signals pins 29, 31, 35,
37, and 67.
•
Changes to Table 36. Rx Sensitivity – LTE
