LN930 M.2 Hardware User Guide
1VV0301078 Rev.10 – 2015-11-11
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved.
Page 86 of 88
15
Document History
Revision
Date
Changes
0
2013-05-20
First issue
1
2013-07-09
•
Update setting for Pin 21 on the host interface. This signal is not connected.
•
Updated pin names of pins 1, 21, 69, and 75 in Table 4 and Table 19 to
simply reflect HW Configuration use.
•
Updated Table 24 to indicate configuration pins 1, 69, and 75 are tied to
GND.
•
Rename section 3.6 Coexistence Interface to In-Device Coexistence
Interface. Additional information on the Inter-device coexistence support was added.
•
Updated section 4.1.3 System Trace Tool Section.
•
Updated Figure 5 – RF Engine for WW SKU.
•
Add further information USB LPM to USB section
•
Added information on Seamless Roaming & Wifi Off-load – SIM_EAP,
SIM-AKA under Other Requirements
•
Added information on Antenna Design Guidelines under Other
Requirements.
2
2013-07-29
RF bands updated
3
2013-08-26
Updating on RF bands
Updated section 3.5 and 3.4.5
Updated temp range
4
2013-09-09
HN930-DC product was removed from portfolio
5
2013-09-15
Main & Diversity antenna positions have been swapped.
•
Updated documentation accordingly, Figure 6 and Figure 10.
•
Updated WWAN M.2 Mechanical drawings, Figure 14 through Figure 17.
•
Updated Card_power_ON_OFF description for UltraBook in Table 9.
•
Updated comments in Table 15 regarding the DPR#/SAR signal.
•
Updated SIM DTECTED signal to indicate an external pull-up.
•
Updated Platform Block Diagrams to show DPR# signal is connected to an
EINT pin (not GPIO) on XGOLD.
•
Identified Audio Signals on host interface in Table 4. Previously these were
simply defined as Reserved.
•
Updated VBAT requirements in Table 24 and Table 25.
6
2013-11-20
•
Regulation section was updated
•
Adding support for UMTS Band 6 to M.2 APAC SKU (see Table 2).
•
Updated 3G RF Band support for APAC Module, supported bands are 1, 8,
11, and 19. (see Table 2)
•
Added Measured Values for 2G/3G Rx Sensitivity Table 31 and Table 32.
•
Update Measured Value and changed header name in Rx Sensitivity LTE
Table 33
•
Modified supply voltage lower spec for Ultra book in Table 24.
•
Update Table 4, Table 6, Table 26 voltage levels for USB and SIM pins.
•
Added LTE conditions and added Table 33.
7
2014-04-10
•
Added SSIC to ICP interface. Updated RESET signal definition. Updated
Antenna figures.
•
Updated Conducted Transmit Power requirements, Table 32.
•
Section 2.2, Table 4
•
Changed UIM signals pins 30, 32, 34, 36
•
Replaced dash with underscore in signal names.
•
Changed supply voltage for Antenna Tuning Signal
(ANTCTL*) from (1.7 V – 2.6 V) to 1.8 V.
•
Section 3.5, Table 20 changed supply voltage for Antenna Tuning Signals
(ANTCTL*) from (1.7 V – 2.6 V) to 1.8 V.
•
Section 3.11, Table 25 correction to both no connect pins and key slot pins.
•
Section 8.2, Table 27
o
Changed the max voltage to 3.0 V for WAKE_WWAN# signal
o
Changed Typ voltage and max voltage for the Antenna Tuning
Signals to 0/1.8 V and 2.3 V respectfully
