a couple of cable ties, this to make up for the long cables. You may for
example place one of the DPA 4060 mics inside the Zeppelin holder, and
another one at the edge (side) of the dish. This requires some DIY
configuration (and som patience) but has proven good results.
ñ
Adjustable cable length from handle in both directions (1.5 meters)
- allows for many different type of applications without having to
use adapters. Pull the cable in any direction to adjust the cable
length from the bottom of the handle to the recorder – and from the
top handle to the microphone.
ñ
When extending the cable from the bottom of the handle to the
recorder, start with pushing the cable going from the top of the
handle - further into the handle body, and pull out the cable from
the handle bottom until you have the desired length in both
directions.
*
New adjustable gray cylinder shaped "stopper" – pre attached to
the cable and easily secured in the tube of the included mounting kit.
This to prevent unwanted sounds to travel to the microphone from
the back of the dish, especially when using a cardioid mic facing the
dish. The cylinder shaped stopper may be placed in
vertical/horizontal position of the dish center hole, or at the
beginning of the tube, it all depends which microphone and
configuration you wish to use. If you are using a longer type of omni
microphone, which may be too long to mount facing the dish, you
can leave the stopper resting on the cable outside the tube.
TELINGA UNIVERSAL MK2 PACKAGE INCLUDES:
(1)
UNIVERSAL MK2 HANDLE INCL. 1.5 METER LENGTH ADJUSTABLE XLR
CABLE WITH GOLD PLATED NEUTRIK XLR CONNECTORS
(1)
UNIVERSAL MK2 ZEPPELIN MICROPHONE HOLDER
(1)
MOUNTING KIT HOLDING ANY OF OUR DISHES
(1)
PARABOLIC DISH (V2 FOLDABLE OR STATIONARY)
(1)
PRE INSTALLED SET OF RED RUBBER MIC HOLDERS LOCATED AT
FRONT OF THE ZEPPELIN HOLDER.
IMPORTANT! ONLY USE THE RED RUBBER BANDS LOCATED AT THE
FRONT OF THE ZEPPELIN HOLDER WHEN A MICROPHONE IS MOUNTED
FACING THE DISH.
OPTIONAL ACCESSORIES:
TRIPOD MOUNT, SOFT CASE, RYCOTE DISH
HWC, RECORDER HOLDER.
and easily secured in the tube of the included mounting kit.
New adjustable gray cylinder shaped "stopper" – pre attached
Adjustable wire length from handle in both directions (1.5 meters)
use adapters. Pull the wire in any direction to adjust the
When extending the wire from the bottom of the handle to the
recorder, start with pushing the wire going from the top of the
handle - further into the handle body, and pull it out from
- allows for many different type of applications without having to
PRE INSTALLED SET OF RED RUBBER MIC HOLDERS LOCATED AT
FRONT OF THE ZEPPELIN HOLDER.
MOUNTING KIT HOLDING THE TELINGA (V2) FOLDABLE DISH.
UNIVERSAL MK2 ZEPPELIN MICROPHONE HOLDER TO MOUNT INSIDE DISH.
WIRE WITH GOLD PLATED NEUTRIK XLR CONNECTORS.
UNIVERSAL MK2 HANDLE INCL. 1.5 METER LENGTH ADJUSTABLE XLR
TELINGA (V2) PARABOLIC DISH.
HWC, TELINGA DISH HWC.
TRIPOD MOUNT, SOFT CASE, RYCOTE TELINGA DISH
length from the bottom of the handle to the recorder – and from the
top handle to your microphone.
dish. The cylinder shaped stopper may be placed in
vertical/horizontal position of the dish center hole, or at the
beginning of the tube, it all depends which microphone and
configuration you wish to use. If you are using a longer type of omni
microphone, which may be too long to mount facing the dish, you
This to prevent unwanted sounds to travel to the microphone from
the back of the dish, especially when using a cardioid mic facing the
can leave the stopper resting on the Universal wire outside the tube.
