manualshive.com logo in svg

Telindus 1110ADSL Bridge, User Manual, Page: 17 / 46

Share
Download
Telindus 1110ADSL Bridge User Manual Download Page 17

User’s Guide

December, 2002

9

CHAPTER 3:

NETWORK CONFIGURATION

3.1 USB Driver Installation

If you are connecting your Telindus 1110/1111 ADSL Bridge using its USB interface, you will 
need to install the USB software driver. Please follow the steps below to ensure a successful 
USB installation.

If you do not plan to use the USB interface, skip the sections below and move on to the next 
section titled “

TCP/IP Installation

”.

NOTE: USB interface is only supported using Windows 98SE/2000/Me/XP operating sys-

tems.

The following instructions will help you complete the USB installation procedure:

NOTE:

DO NOT

 plug the USB cable from the PC into the USB connector on the device 

until instructed to do so.

3.1.1 Installing USB Drivers on Windows 98SE/ME

Step 1.

Place the included CD into the appropriate CD-ROM drive. Locate the USB Driver folder in 
the CD-ROM and click the 

USB Setup.exe

 to install the USB driver.           

              

Step 2.

Plug the USB cable into the PC from ADSL 
Bridge when you are instructed to do so.

Summary of Contents for 1110ADSL Bridge















































Reviews:

No comments