Setup & Programming the Operating Parameters in the Telguard TG-7 models
When the Telguard is received from the factory, registered and is powered up for the first time, it is ready for activation, provided the default settings are what you want. The STC LED
# 2 will flash to indicate any failure conditions. The Mode LED # 3 will be on and the STC 1 and STC 2 relays will be tripped. The Telguard can be programmed using a line-mans butt-
set connected to T & R Test Points.
TO PROGRAM THE Telguard TG-7
A.
Put the line-mans butt-set in talk mode.
B.
Dial “###’,*, you will hear 2 beeps.
C.
Press #, *, this will put the Telguard into a Master Access programming mode, 2 beeps.
D.
Enter changes required. The syntax for programming a specific memory location is as follows:
MEMORY LOCATION (3-digits), will respond with 2 beeps, then VALUE, will respond with 2 beeps
.
E.
Then press *, you will hear 2 beeps then hang up. This saves the change and exits the programming mode.
Mem Loc.
Field
Default Value
Setting
831
Mode of operation
01
1 = Telco Primary/Cellular Backup
2 = Cellular Primary/Telco Backup
3 = Cell Only
833
C/C Reporting Format
09
01 = 4x2 pulse, 40pps, 2300 hz
02 = 4x2 pulse, 20pps, 2300 hz
03 = 4x2 pulse, 10pps, 1400 hz
04 = 3x1 pulse, 40pps, 2300 hz
05 = 3x1 pulse, 20pps, 2300 hz
06 = 3x1 pulse, 10pps, 1400 hz
07 = Radionics IIe or IIIa
2
08 = Contact ID
09 = Auto Format Detect
11 = SIA2 (300 Baud)
12 = DMP
845
Manual Battery Test
N/A
Initiates the on-demand battery test
850
STC1 Trip Output
Reporting
Normally Open
04
(LFC only)
Enter the SUM TOTAL of the events that you wish to trip the STC relay by ADDING the corresponding values:
00 = Not Used
01 = AC Failure
02 = Low Battery
04 = LFC
08 = NSC
16 = RFC
32 = DTF
63 = ALL
851
STC2 Trip Output
Reporting
Normally Closed
59
(all except LFC)
Enter the SUM TOTAL of the events that you wish to trip the STC relay by ADDING the corresponding values:
00 = Not Used
01 = AC Failure
02 = Low Battery
04 = LFC
08 = NSC
16 = RFC
32 = DTF
63 = ALL
852
STC Trip Delay for NSC
2 (60 sec)
1=30 seconds
4=10 minutes
7=45 minutes
2=60 seconds
5=20 minutes
8=60 minutes
3=3 minutes
6=30 minutes
9=24 hours
858 STC
History
N/A
0 = terminate STC history display mode
1 = start STC history display mode
2 = clear STC history
861
CFC Number of Events
0 (disabled)
0 = disabled
2 = 4 attempts
1 = 2 attempts
3 = 8 attempts
862
CFC Between Events
1 (30 sec)
1 = 30 seconds
3 = 70 seconds
5 = 90 seconds
2 = 60 seconds
4 = 80 seconds
6 = 99 seconds
868
PPF Delay
0 (disabled)
0 = disabled,
1 = 10 seconds,
2=20 seconds, … 15=150 seconds
872
AC Failure Delay
02 (2 hours)
0-24 hours
873
Trip Input Reporting
0 (no report)
0 = no report
1 = report trip
874
Trip Input Restoral Reporting
0 (no report)
0 = no report
1 = report restoral
875
Trip Input Swinger Function
0 (disabled)
0 = swinger function disabled
1 = swinger function enabled
899
Factory Default Unit
N/A
Resets all settings to factory defaults
NOTE: SPECIAL LED INDICATIONS DURING ACTIVATION
If the Telguard fails to confirm activation it will be displayed on the LEDS:
System Status LEDs
Activation Indications
LEDS 1-5 FLASHING
FAILED ACTIVATION – SIGNAL TOO WEAK
LED #1 & LED #4 FLASHING
ACTIVATION ERROR – CALL TECH SUPPORT
LED #1 ON
ACTIVATION SUCCESSFUL
LED #1 OFF
NOT ACTIVATED. NEED TO CONNECT PANEL AND TRIP ZONE
On either a FAILED ACTIVATION or ACTIVATION ERROR, the unit MUST BE RESET BY PRESSING THE RSSI BUTTON TWICE. The activation message MUST BE RESENT or the TELGUARD will
not transmit signals through the cellular network. Repeat step 4 above.
