Telex RTS SPK300L User Manual Download Page 5

3

Specifications

Specifications

FIGURE 1.

SPK300L Block Diagram

Audio Line 
Voltage

1 volt, peak (0 dBm voltage-equivalent)

Average 
Speech Level 
Range

-20 dBV to -10 dBV

Absolute 
Maximum 
Speech Level

3 volts, peak (linear limit)

Audio Line 
Impedance, 
Nominal

200 50 ohms, 75 Hz to 20 kHz
System will continue to operate from 50 ohms to 300 
ohms.

SYSTEM DC CURRENT

Nominal

32 volts DC

Operational 
Range 

18 to 35 volts DC

Steady state 
without 
damage

-1.5 volts to 36 volts DC

Transient

200 volts, 8 milliseconds or less (after this time, power 
supply and user station fuses will open).

System DC 
Current

Quiescent 
(per station)

10 to 40 milliamps

Dynamic (per 
station)

50 milliamps (w/25 ohm headphones)
70 milliamps (w/25 ohm headphones and lights)
100 milliamps (w/8 ohm speaker)

Start-Up 
Current

1.25 amperes, 50 units, all kinds

Fault Current

4.0 amperes, power supply at voltage >12 volts
1.0 amperes, power supply at voltage <12 volts

OPERATING DISTANCES

Maximum DC 
limit

5,000 ft distance along cable, power supply to single 
station #22 gauge wire - DC voltage drop limitation.

Maximum AC 
limit

10,000 ft. dry pair,, power supply at each end, #22 gauge 
wire

System 
Capacitance

0.3 microgarads (cumulative effect of 10,000 ft. of 
maximum cable at 30 picofarads/foot)

USER STATIONS SPECIFICATIONS

Input DC 
voltage

20 to 35 volts DC, operating from -200 to +36 volts DC 
without damage.

DC Current

Quiescent, 10 to 40 milliamps
50 milliamps, typical (w/25 ohms headphones)
75 milliamps, typical (w/25 ohms head lights)
100 milliamps, typical (w/8 ohm speaker)

Impedance 
Across Line

10,000 ohms typical; 2,000 ohms worst case dynamic 
operation

Ambient 
Temperature 
Range

Operating 0° C to 60° C (0° F to 140° F)
Storage -55° C to 125° C (-67° F to 257° F)

Noise 
Contribution 
to 200 ohm 
Line

One unit: -75 dBu
Ten unit: -67 dBu

MICROPHONE PREAMPLIFIER

Imput 
Impedence *

470 ohms

Source 
Impedance*

200 ohms, nominal

Maximum 
Input Level

150 millivolts

Voltage Gain

54 dB

Frequency 
Response

100 Hz to 10,000 Hz, 3 dB

Summary of Contents for RTS SPK300L







































Reviews: