background image

ii

P

ROPRIETARY

 N

OTICE

The product information and design disclosed herein were originated by 
and are the property of Telex Communications, Inc. Telex reserves all 
patent, proprietary design, manufacturing, reproduction, use and sales 
rights thereto, and to any article disclosed therein, except to the extent 
rights are expressly granted to others.

C

OPYRIGHT

 N

OTICE

Copyright 2006 by Telex Communications, Inc. All rights reserved. 
Reproduction, in whole or in part, without prior written permission from 
Telex is prohibited.

W

ARRANTY

 N

OTICE

See the enclosed warranty card for further details.

C

USTOMER

 S

UPPORT

Technical questions should be directed to:

Customer Service Department
RTS/Telex Communications, Inc.
12000 Portland Avenue South
Burnsville, MN 55337 USA
Telephone: 800-392-3497
Fax: 800-323-0498
Factory Service: 800-553-5992

R

ETURN

 S

HIPPING

 I

NSTRUCTIONS

Customer Service DepartmentTelex Communications, Inc. (Lincoln, 
NE)
Telephone: 402-467-5321
Fax: 402-467-3279
Factory Service: 800-553-5992

Please include a note in the box which supplies the company name, 
address, phone number, a person to contact regarding the repair, the type 
and quantity of equipment, a description of the problem and the serial 
number(s).

Shipping to the Manufacturer

All shipments of product should be made via UPS Ground, prepaid (you 
may request from Factory Service a different shipment method). Any 
shipment upgrades will be paid by the customer. The equipment should 
be shipped in the original packing carton. If the original carton is not 
available, use any suitable container that is rigid and of adequate size. If 
a substitute container is used, the equipment should be wrapped in paper 
and surrounded with at least four (4) inches of excelsior or similar 
shock-absorbing material. All shipments must be sent to the following 
address and must include the Proof of Purchase for warranty repair. 
Upon completion of any repair the equipment will be returned via 
United Parcel Service or specified shipper, collect.

Factory Service Department
Telex Communications, Inc.
8601 Cornhusker Hwy.
Lincoln, NE 68507 U.S.A.
Attn: Service

This package should include the following:

FIGURE 1.

TW System Concept Block Diagram

Summary of Contents for RTS SPK300L







































Reviews: