TELEVAC MX7M Page 3 Instruction Manual Download | Manualshive

Page: 3 / 24

background image

Instruction Manual

MX7M Active Gauge

1 Introduction

1.1 Disclaimer

All information in this manual is subject to change without notice. The Fredericks Company assumes
no responsibility for inaccuracies in product specifications or any liability arising from product use.
Please contact Televac at

[email protected]

or call +1 215-947-2500 with comments or

questions.

1.2 Description

The MX7M is cold cathode ionization gauge with a measurement range of 5

×

10

−

11

Torr to 1

×

10

−

2

Torr.

It utilizes a Televac cold cathode ionization sensor in the inverted magnetron configuration with part
numbers 2-2183-KF25 (KF25 flange version), 2-2183-KF40 (KF40 flange version), 2-2183-KF16 (KF16
flange version) or 2-2183-CF40 (CF40 flange version). It has a two color OLED display with selectable
units of Torr, Millibar, and Kilopascal. Settings can be changed through RS-485 communications with
a PC, through USB communications with a PC, or through the unit’s front panel using four capacitive
touch buttons located on the top of the unit. The MX7M has two set points, one relay and one open
collector, and a selectable analog output option. The analog output is a configurable 0-10 V output
that includes options for linear, linear-by-decade, and logarithmic formats.

1.3 Operating Specifications

Table 1: Operating Specifications

Operating Range

5

×

10

−

11

to 1

×

10

−

2

Torr

Communications

RS-485 and USB

Programmable Set Points

2

Set Point 1

Open Collector

Set Point 2

Relay

Analog Output

Configurable 0 to 10 V

Supply Voltage

+22 to +26 V DC

Maximum Power

8 W

Calibration Medium

Dry air or nitrogen

Overpressure

150 PSI

Digital Output Resolution

2 significant digits with exponent

Analog Output Resolution

16 bits

Operating Temperature

0

◦

C to 50

◦

C

Storage Temperature

−

20

◦

C to 60

◦

C

Bakeout Temperature

250

◦

C (electronics removed)

Response Time

≤

1 second

Accuracy

1

×

10

−

9

Torr to 1

×

10

−

3

Torr

±

30%

Analog Output

±

10 mV

Display Readable Distance

3 m (10 feet)

email: [email protected]

tel: +1 215 947 2500

web: frederickscompany.com

mx7m_im rev C

2 of 23

«
1
2
3
4
5
...
»

Summary of Contents for MX7M

























Reviews:

No comments

Related manuals for MX7M

Brand: OHAUS Pages: 100

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands