TELEVAC MX7M Instruction Manual Download | Manualshive

Page: 24 / 24

background image

Instruction Manual

MX7M Active Gauge

3.6 RS-485 and USB Communications Error Codes

Table 12: RS-485 and USB Communications Error Codes

Error Codes

Description

0N0001<cr><lf>

Command error: an invalid character was sent for the
command or an invalid number after the character.

0N0002<cr><lf>

Units error: an invalid parameter was sent after a com-
mand specifier

Table 13: RS-485 and USB Status Commands

Command

Response

Description

S1

ppsee

Read pressure data where ppsee is:
pp = mantissa
s = sign
ee = exponent
When in the “Starting” state, unit returns “Starting”
When in the “Low” state, unit returns “Low”
When high voltage is off, unit returns "0"

S2

yymmdd

Read firmware version, where:
yy = last two digits of year
mm = month
dd = day

3.7 Firmware Updates

The MX7M has the ability to update the firmware when in the field over the USB communications. For
more information on updating the firmware, please contact

[email protected]

email: [email protected]

tel: +1 215 947 2500

web: frederickscompany.com

mx7m_im rev C

23 of 23

«
...
22
23
24

Summary of Contents for MX7M

























Reviews:

No comments

Related manuals for MX7M

Brand: RA Fischer Pages: 36

Brand: Transforming Technologies Pages: 12

Brand: EMC Pages: 39

Brand: Core Insight Pages: 24

Brand: Core Insight Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands