manualshive.com logo in svg

Teledyne T101, Operation Manual, Page: 85 / 375

Share
Download
Teledyne T101 Operation Manual Download Page 85

Teledyne ML – T101 Operation Manual 

Operating Instructions 

 

81 

4.6.

 

SETUP – DIAG: USING THE DIAGNOSTICS 

FUNCTIONS 

 

A series of diagnostic tools is grouped together under the 

SETUP

MORE

DIAG 

menu.  As  these  parameters are dependent on firmware revision (see Menu Tree A-5 in 
Appendix A). The individual parameters, however, are explained in more detail in the 
following section, indicated in Table  4-8. These tools can be used in a variety of 
troubleshooting and diagnostic procedures and are referred to in many places of the 
maintenance and trouble-shooting sections. 

Table 4-8. T101 Diagnostic (DIAG) Functions 

DIAGNOSTIC FUNCTION AND MEANING 

FRONT PANEL 

MODE 

INDICATOR 

SECTION 

SIGNAL I/O:  Allows observation of all digital and analog signals in the 

instrument. Allows certain digital signals such as valves and heaters to be 

toggled ON and OFF. 

DIAG I/O 

4.6.1 

ANALOG OUTPUT: When entered, the analyzer performs an analog 

output step test. This can be used to calibrate a chart recorder or to test 

the analog output accuracy. 

DIAG AOUT 

4.6.2 

ANALOG I/O CONFIGURATION: Analog input/output parameters are 

available for viewing and configuration. 

DIAG AIO 

4.6.3 

OPTIC TEST When activated, the analyzer performs an optic test, which 

turns on an LED located inside the sensor module near the PMT (Fig. 10-

15). This diagnostic tests the response of the PMT without having to 

supply span gas. 

DIAG OPTIC 

4.6.4 

ELECTRICAL TEST:  When activated, the analyzer performs an electric 

test, which generates a current intended to simulate the PMT output to 

verify the signal handling and conditioning of the PMT preamp board. 

DIAG ELEC 

4.6.5 

LAMP CALIBRATION:  The analyzer records the current voltage output 

of the UV source reference detector.  This value is used by the CPU to 

calculate the lamp ration used in determining the H

2

S/SO

2

 concentration 

(see  10.2.2) 

DIAG LAMP 

4.6.6 

PRESSURE CALIBRATION:  The analyzer records the current output of 

the sample gas pressure sensor.  This value is used by the CPU to 

compensate the H

2

S concentration when the TPC feature is enabled. 

DIAG PCAL 

4.6.7 

FLOW CALIBRATION:  This function is used to calibrate the gas flow 

output signals of sample gas and ozone supply. These settings are 

retained when exiting DIAG. 

DIAG FCAL 

4.6.8 

TEST CHAN OUTPUT: Configures the A4 analog output channel. 

DIAG TCHN 

4.6.9 

Summary of Contents for T101
























































































































































































































































































































































































Reviews:

No comments