Teledyne HVG-2020B Instruction Manual Download Page 4

Page: 4 / 40

HVG-2020B Instruction Manual

EAR99 Technology Subject to Restrictions Contained on the Cover Page

Page 4 of 40

OSITIVE

RESSURE

PERATION

....................................................................................... 24

EMPERATURE AND

UMIDITY

FFECTS

................................................................................ 24

IRANI AND

NTERACTIONS

........................................................................................ 25

ALIBRATION

ROCEDURE

............................................................................................. 25

DIGITAL OPERATION .................................................................................................... 27

NSTRUMENT

TATES

.................................................................................................. 27

ERIAL

OMMUNICATIONS

............................................................................................. 27

5.2.1.

General ...................................................................................................... 27

5.2.2.

Serial Communication Software.......................................................................... 27

5.2.3.

The Sensor Lists ............................................................................................ 27

5.2.4.

Command Prompt .......................................................................................... 27

5.2.5.

Command Format .......................................................................................... 28

5.2.6.

RS232 / RS485 Mode ....................................................................................... 28

5.2.7.

Response Format ........................................................................................... 28

5.2.7.1.

Response Line Termination ......................................................................................... 28

5.2.7.2.

RS485 Mode Responses .............................................................................................. 29

5.2.8.

Commands ................................................................................................... 29

5.2.8.1.

Reporting Commands ................................................................................................ 29

5.2.8.2.

System Commands ................................................................................................... 29

5.2.8.3.

State Commands ..................................................................................................... 32

5.2.8.4.

Sensor List Commands .............................................................................................. 33

TROUBLESHOOTING .................................................................................................... 38

UTHORIZED

AINTENANCE

........................................................................................... 38

ROUBLESHOOTING

................................................................................................... 38

6.2.1.

Instrument Lists and Codes ............................................................................... 38

6.2.2.

Possible Problems and Solutions ......................................................................... 38

WARRANTY ............................................................................................................... 39

ARRANTY

OLICY

................................................................................................... 39

ETURN

OLICY

...................................................................................................... 39

DRAWINGS ................................................................................................................ 40

Summary of Contents for HVG-2020B









































Search results

Summary of Contents for HVG-2020B

Reviews:

Teledyne HVG-2020B, Instruction Manual, Page: 4 / 40

Search results

Summary of Contents for HVG-2020B

Reviews: