manualshive.com logo in svg

Teledyne HVG-2020B, Instruction Manual, Page: 21 / 40

Share
Download
Teledyne HVG-2020B Instruction Manual Download Page 21

HVG-2020B Instruction Manual

 

 EAR99 Technology Subject to Restrictions Contained on the Cover Page

 

Page 21 of 40 

 

3.  Display Operation 

 

General 

The HVG-2020B has an optional color touch screen module that can be assembled with the internal I/O module 

to provide the user with local control over device operation. All operations done via the touch screen utilize 
the values associated with the digital lists and commands found in Section 4. 

The resistive touch panel will allow items other than your finger to activate the touch, such as a stylus, pencil 
eraser, fingernail, gloved finger... etc. However, it can only detect one touch location at a time. The touch 
panel top layer is made of polyester, or polyethylene terephthalate (PET). 

 

NOTICE:

 Do not apply excessive pressure, liquids or sharp objects to the touch screen to avoid damage. 

To clean the display, breathe on the surface and gently wipe it with a soft cotton or microfiber cloth. 

 

 

VIEW Icon 

The VIEW icon allows the user to cycle through five possible main screens (views). The VIEW and MENU icons 

remain visible in the bottom corners of the screen in all views. Some items displayed in the different Views 
allow the user to toggle or adjust them. 

 

 

View 

Icon

 

Menu 

Icon

 

Summary of Contents for HVG-2020B









































Reviews:

No comments