manualshive.com logo in svg

Teledyne 3300TB, Operating Instructions Manual, Page: 30 / 51

Share
Download
Teledyne 3300TB Operating Instructions Manual Download Page 30

Trace Oxygen Analyzer 

Installation 

 

 

Teledyne Analytical Instruments  

17 

 

 

 

switching up to 0.5 ampere at 125 VAC into a resistive load (2A for 30 
VDC). 

The alarm relay circuits are designed for failsafe operation, 

meaning the relays are energized during normal operation. If power fails 
the relays de-energize (alarms activated). 

The contact connections are indicated diagrammatically on the rear 

panel as Normally Closed, Common, and Normally Open. Figure 3-2 
explains how these act in failsafe operation. 

Alarm 1 and Alarm 2   can both be configured as either HI or LO.  

A HI alarm will activate when concentration is above threshold, while a 
LO alarm will activate concentration is below threshold. 

 

 

 

Figure 3-2: Contact ID for FAILSAFE Relay Operation 

 

The specific descriptions for each type of alarm are as follows: 

Alarm #1

 

Programmable as high or low alarm (actuates when 
concentration is above threshold). Can be set 
anywhere between 0 and 9999ppm, but must be set 
ABOVE the threshold set for the LO Alarm. 

Alarm #2

 

Programmable as high or low alarm (actuates when 
concentration is below threshold). Can be set 
anywhere from 0 to 9999ppm. 

Sensor Fail

 

Actuates when the output of the  Micro-Fuel Cell 
sensor falls below the acceptable level. 

 

Summary of Contents for 3300TB




















































Reviews:

No comments