Teledyne 2240 Manual Download Page 2

Page 3 of 26 

M2240

 R0 

ATMOSPHERE (AIR OR NITROGEN) 
UNTIL THE DISPLAY READS <0.001%.   
 

4)  

TELEDYNE

, IS NOT RESPONSIBLE FOR 

THE ACTIONS TAKEN BY THE USERS OF 

2240

 (SEE FOLLOWING FOR MORE 
DETAILS ON 

TELEDYNE'S

 LIMITED 

LIABILITY.) 

 
5)

 

Teledyne

 WARRANTS ONLY THAT THE 

2240

 MEETS 

TELEDYNE'S

 PUBLISHED 

SPECIFICATIONS AT THE TIME OF 
PURCHASE, AND DISCLAIMS ALL 
OTHER WARRANTIES (SEE BELOW FOR 
MORE DETAILS ON 

TELEDYNE'S

 LIMITED 

WARRANTY.) 

 

Page 4 of 26 

M2240

 R0 

LIMITED WARRANTY 

 

Teledyne 

Limited Warranty

. Each 

2240

 portable hand-held 

hydrogen instrument (“Product”) will conform, as to all substantial 
operational features, to the Product specifications set forth in this Manual 
and will be free of defects which substantially affect such Product’s 
performance for twelve (12) months from the ship date for such Product. 

Must Provide Notice of Defect

.  If you believe a Product that you 

believe is defective, you must notify 

Teledyne

 in writing, within ten (10) 

days of receipt of such Product, of your claim regarding any such defect.   

Return Product to H2scan for Repair, Replacement or Credit

.  If the 

Product is found defective by 

Teledyne

Teledyne's

 sole obligation under 

this warranty is to either (i) repair the Product, (ii) replace the Product,

 

or 

(iii) issue a credit for the purchase price for such Product, the particular 
remedy to be determined by 

Teledyne

 on a case-by-case basis.   

 
Limitation of Warranty

.  THE ABOVE IS A LIMITED WARRANTY 

AS IT IS THE ONLY WARRANTY MADE BY 

TELEDYNE

.  

TELEDYNE

 

MAKES NO OTHER WARRANTY EXPRESS OR IMPLIED AND 
EXPRESSLY EXCLUDES ALL WARRANTIES OF 
MERCHANTABILITY AND FITNESS FOR A PARTICULAR 
PURPOSE.  YOUR SOLE REMEDY HEREUNDER IS REPAIR OR 
REPLACEMENT OF THE PRODUCT OR A CREDIT FOR THE 
PURCHASE PRICE FOR SUCH PRODUCT, THE PARTICULAR 
REMEDY TO BE DETERMINED BY 

TELEDYNE

 ON A CASE-BY-

CASE BASIS.  

TELEDYNE

 SHALL HAVE NO LIABILITY WITH 

RESPECT TO ITS OBLIGATIONS UNDER THIS AGREEMENT FOR 
CONSEQUENTIAL, EXEMPLARY, OR INCIDENTAL DAMAGES 
EVEN IF IT HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH 
DAMAGES.  THE STATED EXPRESS WARRANTY IS IN LIEU OF 
ALL LIABILITIES OR OBLIGATIONS OF 

TELEDYNE

 FOR 

DAMAGES ARISING OUT OF OR IN CONNECTION WITH THE 
DELIVERY, USE OR PERFORMANCE OF THE PRODUCTS. 

 

LIMITATION OF LIABILITY 
IN THE EVENT OF A DEFECT IN A PRODUCT, 

TELEDYNE

 SHALL NOT BE RESPONSIBLE FOR ANY 
DIRECT, INDIRECT, INCIDENTAL OR 
CONSEQUENTIAL DAMAGES RESULTING THERE 
FROM, INCLUDING, BUT NOT LIMITED TO, LOSS 
OF REVENUE AND/OR PROFIT

.   

Summary of Contents for 2240














Reviews: