Teledyne 2240 Manual Download | Manualshive

Page: 12 / 13

background image

Page 23 of 26

M2240

R0

8. Charging the

2240 battery

Equipment Required

•

Battery Charger Power Supply

•

Power Cord for country of use

•

Battery Charger

•

Single Bay Battery Charger

•

Optional Dual Bay Battery Charger

Figure 4 -

2240

Dual Bay Battery Charger (optional)

with Power Supply and Power Cord

Page 24 of 26

M2240

R0

Charging/Re-Charging the Battery(ies)

•

Plug the power cord into the Power Supply and insert
the DC output plug into the socket on the Battery
Charger.

•

Plug the power cord into an appropriate AC outlet.
The charging status lamp(s) will flash yellow then turn
off.

•

Plug the battery (or two batteries with optional Dual
Bay Battery Charger) into the pocket of the Battery
Charger. Make sure the battery is oriented properly
and firmly seated down onto the connector blades
(batteries installed backwards will not make contact).
The status lamp(s) will illuminate to indicate the status
of the batteries as follows:

•

OFF - No battery detected

•

Red - Charging

•

Green - Battery fully charged

•

Yellow - Standby

•

Flashing Red - Error

«
...
10
11
12
13
»

Summary of Contents for 2240














Reviews:

No comments

Related manuals for 2240

Brand: L-Sniper Pages: 12

Brand: SAA Asia Limited Pages: 76

Brand: Caddx-Caddi Controls Pages: 6

Brand: +360 Pages: 9

Brand: Lorex Pages: 2

Brand: Axis Pages: 32

Brand: Hanwha Vision Pages: 65

Brand: dallmeier Pages: 40

Brand: Idis Pages: 24

Brand: IA Technologies Pages: 10

Brand: Chuango Pages: 52

RWS-XE5DIP3610M-IR

Brand: Ronix Pages: 28

Brand: Datavideo Pages: 100

Brand: NookBox Pages: 8

Brand: Eagle Eye Networks Pages: 5

Brand: Iget Pages: 21

Brand: Gemini Pages: 16

Brand: Weldex Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands