background image

I SERIES V oIP USER GUIDE    

www.teledexeurope.com

 

13

Configure to dynamically obtain the IP.

Enable DHCP.

If there is a DHCP server in your local network, 
the I Series phone will automatically obtain the 
WAN port network information from your DHCP 
server.

CONFIGURE PPPOE

–  Enable PPPoE
–  PPPoE Server: Enter “ANY” if not specified 

from your ITSP

–  Enter PPPoE username and pin in the 

Username and Password entries

The I Series phone will automatically obtain the 
WAN  port  network  information  from  your  ITSP 
if  the  PPPoE  setting  and  the  setup  are  correct. 

Note:

  If  a  user  accesses  the  IP  phone  through 

a  WAN  port  he  or  she  should  use  the  new  IP 
address  to  access  the  IP  phone  when  the  WAN 
port address was changed.

3.3.2 LAN CONFIGURATION

LAN IP:

 This is where you can set the IP address 

of the phone (at its LAN port). This is seldom used 
because  in  most  environments  Bridge  Mode  is 
enabled, causing the LAN port to act as a bridged 
extension of the WAN port.

Netmask: 

Set the IP Subnet mask for the LAN.

DHCP Service:

 Enable DHCP service on the LAN 

port. After the user changes LAN IP, the phone 

will automatically modify the DHCP Lease Table 
and  save  the  configuration  according  to  the  IP 
and  netmask  information.  The  DHCP  server 
configuration  won’t  take  effect  until  you  reboot 
the device.

NAT:

 Enable Network Address Translation (NAT) 

for navigating through firewalls.

Bridge  Mode:

  Enable  this  option  to  switch  to 

Bridge  Mode.  An  IP  phone  won’t  assign  an 
internally generated IP for its LAN port in Bridge 
Mode. Most hotel properties will bridge the LAN 
and  WAN  port,  but  separate  the  Guest  network 
from the Hotel’s IP/PBX by implementing VLANs 
(Virtual  LAN’s).  (This  setting  won’t  take  effect 
unless you save the configuration and reboot the 
device.)

3.4 VoIP

3.4.1 SIP CONFIGURATION

SETTING PAGE OF PUBLIC SIP SERVER

Server Address: 

The IP address of the SIP server 

that the SIP phone will attempt to register to.

Server  Port: 

The  Internet  Socket  Port  number 

of the SIP registration server. The default port is 
5060.

Account  Name:

  Username  of  your  SIP  account. 

(Usually the same as the phone number.)

Password:

 Password of your SIP account.

Phone  Number:

  Phone  number  of  your  SIP 

account.

Summary of Contents for I SERIES































Reviews: