Telect Dual-Feed 350A 10/10-TPA User Manual Download Page 11

Page: 11 / 15

1.509.926.6000 :: telect.com

Dual-Feed 350A 8/8-TPA & 10/10

GMT Fuse Alarm Panel

Power

:: 009-8005-0810

1.3 Accessories

The following tables list optional and replacement items for the panel. For wire sizing and labelling, please refer to

Wire Sizing &, Label Convention Chart (Telect Part No. 117995) included with your panel.

WARNING

WARNING! Use only UL-listed fuses or UL-recognized component secondary protection devices.

Table 1 - Accessories

Item

Description

Part Number

Alarm Card, Standard

Power

and

LED Interconnections; Power and Fuse

Alarms

304154

TPA Fuses

124818

10A

124819

15A

124820

20A

124821

30A

122734

40A

122738

50A

122739

GMT Designation Pin Holder

10-Position, Adhesive-Backed Holder for Colored,

Rivet-Shaped GMT Fuse-Current-Rating Pins

101556-1

GMT Fuse Puller

(Recommended)

Medium-Duty, Tweezer-Style Tool for Removing GMT Fuses

06113-03

GMT Phoney Fuse

Dummy Plastic Slug

132748

GMT Fuse Safety Cover

Solder Splash Protection

116915

Summary of Contents for Dual-Feed 350A 10/10-TPA















Search results

Summary of Contents for Dual-Feed 350A 10/10-TPA

Reviews:

Brands by name

Popular brands

Telect Dual-Feed 350A 10/10-TPA, User Manual

Search results

Summary of Contents for Dual-Feed 350A 10/10-TPA

Reviews:

Brands by name

Popular brands