Telect Dual-Feed 350A 10/10-TPA User Manual Download Page 10

Page: 10 / 15

1.509.926.6000 :: telect.com

Dual-Feed 350A 8/8-TPA & 10/10

GMT Fuse Alarm Panel

Power

:: 009-8005-0810

35.

Make sure the load devices are switched off and

then install the fuses:

NOTE: Under load, TPA modules are disconnect

devices only and must not be used to reconnect

power to enabled equipment loads. Reconnecting a

TPA module under power with an enabled load may

damage the TPA module.

• For a TPA fuse, pull out TPA fuse carrier and insert

operable fuse, as shown in Figure 9.

• For a GMT fuse, pull out the dummy fuse, and

insert an operable fuse, as shown in Figure 10.

36.

Test power and polarity at input of each equipment load.

37.

If possible:

• Temporarily replace one of the operable TPA fuses

with a blown fuse to check that the TPA Fuse LEDs

light red. Also, check the

FUSE

alarm terminals on

the rear of the panel:

− Expect an open circuit (00Ω) between Terminals

and

− Expect continuity (0Ω) between Terminals

and

Re-install the operable TPA fuse before proceeding.

• Likewise, replace one of the operable GMT fuses

with a blown fuse to verify that the

FUSE

alarm

terminals are also as specified above. Then re-install

the operable GMT fuse before proceeding.

38.

If desired, connect the remote external audio/visual

alarm indicator wires (solid or tinned wires, #26 to

#20 AWG) to the

PWR

and

FUSE

alarm terminals,

as implied in Figure 11.

39.

Carefully re-install the rear cover.

40. Record the TPA and GMT output destinations in

accordance with operating company procedures

and guidelines.

41.

Turn on equipment loads one at a time to verify the

proper operation of the loads.

TPA Fuse

TPA Fuse Holder

Dummy

Fuse

GMT Fuse

PWR

FUSE

FUSE

To Alarm System

Figure 9 - Installing TPA Fuses

Figure 10 - Installing GMT Fuses

Figure 11 - Wirewrap Alarm Terminal

Connections (Typical)

Summary of Contents for Dual-Feed 350A 10/10-TPA















Search results

Summary of Contents for Dual-Feed 350A 10/10-TPA

Reviews:

Brands by name

Popular brands

Telect Dual-Feed 350A 10/10-TPA, User Manual

Search results

Summary of Contents for Dual-Feed 350A 10/10-TPA

Reviews:

Brands by name

Popular brands