background image

TH-HDMI-KIT

 

 

Rev.:2/7/12 

Figure 5 – Connection of AC/DC power adaptor

 

 

Notice: 

Please DO NOT look directly into the SC receptacles of the Transmitter box, while it is powered 

on, even though this product is regulated strictly enough to operate under the LASER Class I, classified by 
CDRH/FDA for Eye Safety. 

Step 6 

(This step 6 should be done only when the initial installation of THOR-HE-KIT is done or attached 
display is changed.) 

1.

 

 Disconnect the HDMI cable from the Transmitter 

2.

 

Disconnect the AC/DC adapter in Transmitter and connect it again to trigger EDID emulation. 

A.

 

Then, the Transmitter start to read EDID from display and write in it while HDCP LED in 
Transmitter flash around 10 sec. (This could be repeated up to twice.) HDCP LED in Transmitter will 
blink at every 0.5 sec.  (It means EDID emulation is done.)

 

3.

 

Connect Transmitter to HDMI sources over HDMI cable again.   

A.

 

Then, HDCP LED will be turned off.

 

 

Troubleshooting 

The display displays only black screen. 

 

Check that all AC and DC plugs and jacks used by external power supplies (both Telecast and 
others) are firmly connected.   

 

Ensure that power bars are live. 

 

Ensure that the Tx and Rx boxes plug correctly to the media receiver or computer and display, 
respectively. 

 

Check if the media receiver or computer and display are powered on and properly booted. 

 

Re-boot up the system after reconnecting the optical system cable. 

Screen is distorted or displays noises. 

 

Check if the graphic resolution is properly set. Go to the display properties and tap the settings. 
Ensure that the resolution sets less than 1080p (1920x1080) at 60Hz refresh ratio. 

 

Reset the system. 

 

Power down, disconnect and reconnect the optical system cable or DC power adaptors, and 
power up. 

Maintenance 

No special maintenance is required for the optical system cables and power supplies. Ensure that the 
cables and power modules are stored or used in a benign environment free from liquid or dirt 
contamination. 

There are no user serviceable parts.  Refer all service and repair issues to Telecast or its authorized 
distributor. 

Summary of Contents for THOR-HE-KIT









Reviews: