background image

Important safety information

This manual contains information and warnings that must be followed by the user
for safe operation and to keep the product in a safe condition.

To safely perform service on this product, additional information is provided at
the end of this section. (See page , Service safety summary.)

General safety summary

Review the following safety precautions to avoid injury and prevent damage to
this product or any products connected to it.

To avoid potential hazards, use this product only as speci

fi

ed.

Only quali

fi

ed personnel should perform service procedures.

While using this product, you may need to access other parts of a larger system.
Read the safety sections of the other component manuals for warnings and
cautions related to operating the system.

To avoid damage to equipment and personal injury

Do not exceed rackmount weight ratings.

Use this rackmount kit only for the

TSG4100A series instruments.

Use proper hardware.

Do not interchange rack slides or rails with other hardware

or injury may result. Use only rails speci

fi

ed for the slides and mounting screws.

Use care when installing and removing product from rack.

Use two people to

install and remove product from rack, one on each side. Avoid pinching

fi

ngers

and hands when installing and removing. Do not force the product into the rails
when installing. Gently pull the product out when removing.

To prevent the instrument from tipping or dropping onto the installers, two or
more people should install this instrument into the rack cabinet. After completing
the installation procedure, the installers should verify that the instrument and rack
cabinet will not tip forward when the instrument is in the extended position.

The instrument may need to be extended for access to the rear panel. Do not leave
the instrument extended when

fi

nished accessing the rear panel.

Use only with speci

fi

ed products.

Do not use rackmount on products for which

it was not intended. Refer to individual product manuals for details or contact
Tektronix Customer Service when in doubt.

TSG4100A Series RM1 and RM2 Rackmount Kit Instructions

1

Summary of Contents for TSG4100A-RM1














Reviews: