Speci
fi
cations
Table 1: Electrical and mechanical speci
fi
cations
Bandwidth (–3 dB)
800 MHz
System rise time (typical)
<525 ps
System input capacitance
(typical)
1.8 pF
System attenuation accuracy
50:1 ±2.2%
System input resistance @DC
40 M
Ω
±1%
Propagation delay
~6.1 ns
Cable length
1.3 m
Maximum input voltage
(see
Performance Graphs
)
1000 V
RMS
CAT II (2500 V
pk
)
Performance Graphs
Table 2: Environmental speci
fi
cations
Characteristics
Description
Temperature
Operating
Nonoperating
0 °C to +50 °C (+32 °F to +122 °F)
–40 °C to +71 °C (–40 °F to +160 °F)
Humidity
Operating
5% to 95% relative humidity (RH) up to
+30 °C
5% to 75% RH above +30 °C to +65 °C.
Noncondensing
Nonoperating
5% to 45% RH +65 °C to +85 °C.
Noncondensing
Altitude
Operating
Nonoperating
3.0 km (9,842 ft) maximum
15.4 km (50,000 ft) maximum
Table 3: Certi
fi
cations and compliances
Characteristics Description
EC
Declaration
of
Conformity
Compliance was demonstrated to the following
speci
fi
cation as listed in the Of
fi
cial Journal of
the European Communities:
Low Voltage Directive 2006/95/EC:
EN61010-031/A1: 2008
Measurement
Category
Product
Examples
CAT III: Distribution-level mains,
fi
xed
installation
CAT II: Local-level mains, appliances, portable
equipment
CAT I: Circuits not directly connected to mains.
Characteristics Description
Pollution
Degree 2
Do not operate in environments where cond-
uctive pollutants may be present (as de
fi
ned in
IEC 61010-1). Rated for indoor use only.
Additional
Safety
Standards
IEC61010-031; IEC 61010-031/A1:2008
Equipment Recycling.
This product complies
with the European Union’s requirements
according to Directive 2002/96/EC on waste
electrical and electronic equipment (WEEE).
For more information about recycling options,
check the Support/Service section of the
Tektronix Web site (www.tektronix.com).
Safety Summary
Review the following safety precautions to avoid injury and
prevent damage to this product or any products connected
to it. To avoid potential hazards, use this product only as
speci
fi
ed. Using the probe or accessories in a manner not
speci
fi
ed could result in a shock or
fi
re hazard.
To Avoid Fire or Personal Injury
Ground-Referenced Oscilloscope Use.
Do not
fl
oat the
reference lead of this probe when using with ground
referenced oscilloscopes (for example, DPO, MSO, and
TDS series oscilloscopes). The reference lead must be
connected to earth potential (0 V).
Connect and Disconnect Properly.
Connect the probe output
to the measurement instrument before connecting the probe
to the circuit under test. Disconnect the probe input and
the probe reference lead from the circuit under test before
disconnecting the probe from the measurement instrument.
Avoid Electric Shock.
To avoid injury or loss of life, do not
connect or disconnect probes or test leads while they are
connected to a voltage source.
Observe All Terminal Ratings.
To avoid
fi
re or shock hazard,
observe all ratings and markings on the product. Consult
the product manual for further ratings information before
making connections to the product.
Avoid Electric Shock.
When using probe accessories, never
exceed the lowest rating of the probe or its accessory,
whichever is less, including the measurement category and
voltage rating.
Avoid Electric Overload.
To avoid injury or
fi
re hazard, do
not apply potential to any input, including the reference
inputs, that varies from ground by more than the maximum
rating for that input.
Avoid Exposed Circuitry and Do not Operate Without
Covers.
Do not touch exposed connections and components
when power is present.
Inspect The Probe And Accessories.
Before each use,
inspect probe and accessories for damage (cuts, tears,
defects in the probe body, accessories, cable jacket, etc.).
Do not use if damaged.
Do Not Operate in Wet/Damp Conditions.
Do Not Operate in an Explosive Atmosphere.
Keep Product Surfaces Clean and Dry.
Safety Terms and Symbols Terms in This Manual.
These terms may appear in this manual:
WARNING.
Warning statements identify conditions or
practices that could result in injury or loss of life.
CAUTION.
Caution statements identify conditions or
practices that could result in damage to this product or
other property.
Symbols on the Product.
These symbols may appear on
the product:
Contacting Tektronix
Web site:
www.tektronix.com
Phone:
1-800-833-9200
Address:
Tektronix, Inc.
Department or name (if known)
14200 SW Karl Braun Drive
P.O. Box 500
Beaverton, OR 97077 USA
Email:
Warranty Information
For warranty information, go to
www.tektronix.com/warranty.
Copyright © Tektronix, Inc. All rights reserved.
www.tektronix.com
