Tektronix MDO3012, User Manual

Page: 215 / 243

Appendix A: Warranted Speci fi cations
Appendix A: Warranted Speci fi cations
The Analog Bandwidth when the instrument is DC-50 coupled and the Bandwidth Selection if “Full”.
The limits stated below are for ambient temperature of
≤ 30 °C and the bandwidth selection set to FULL.
Reduce the upper bandwidth frequency by 1% for each °C above 30 °C.
Bandwidth 10 mV/div to
1 V/div 5 mV/div to
9.98 mV/div 2 mV/div to
4.98 mV/div 1 mV/div to
1.99 mV/div
1 GHz DC to 1.00 GHz DC to 500 MHz DC to 300 MHz DC to 150 MHz
500 MHz DC to 500 MHz DC to 300 MHz DC to 150 MHz
350 MHz DC to 350 MHz DC to 300 MHz DC to 150 MHz
200 MHz DC to 200 MHz DC to 150 MHz
√ Analog
bandwidth, 50 Ω
100 MHz DC to 100 MHz
√ DC Balance
0.2 div with the input DC-50 Ω coupled and 50 Ω terminated
0.2 div with the input DC-75 Ω coupled and 75 Ω terminated
0.25 div at 2 mV/div with the input DC-50 Ω coupled and 50 Ω terminated
0.25 div at 2 mV/div with the input DC-75 Ω coupled and 75 Ω terminated
0.5 div at 1 mV/div with the input DC-50 Ω coupled and 50 Ω terminated
0.5 div at 1 mV/div with the input DC-75 Ω coupled and 75 Ω terminated
0.2 div with the input DC-1 M Ω coupled and 50 Ω terminated
0.3 div at 1 mV/div with the input DC-1 M Ω coupled and 50 Ω terminated
All above speci fi cations are increased by (0.01 divisions)/( °C) above 40 °C
√ DC Gain
accuracy
±2.5% for 1 mV/div, derated at 0.100%/°C above 30 °C
±2.0% for 2 mV/div, derated at 0.100%/°C above 30 °C
±1.5% for 5 mV/div and above, derated at 0.100%/°C above 30 °C
±3.0% variable gain, derated at 0.100%/°C above 30 °C
Offset, position and the constant offset term must be converted to volts by multiplying by the appropriate
volts/div term.
The basic accuracy speci
fi cation applies directly to any sample and to the following measurements; High,
Low, Max, Min, Mean, Cycle Mean, RMS, and Cycle RMS. The delta volt accuracy speci fi cation applies
to subtractive calculations involving two of these measurements.
The delta volts (difference voltage) accuracy speci
fi cation applies directly to the following measurements;
Positive Overshoot, Negative Overshoot, Pk-Pk, and Amplitude.
The limits are as follows:
Measurement Type DC Accuracy in Volts
Average of > 16 waveforms ±((DC Gain Accuracy) X |reading - (offset - position)| + Offset
Ac 0.1 div)
√ DC Voltage
Measurement
Accuracy, Average
Acquisition mode
Delta Volts between any two averages of
≥ 16 waveforms acquired with the same
scope setup and ambient conditions
±(DC Gain Accuracy X |reading| + 0.05 div)
MDO3000 Series Oscilloscopes User Manual 193