Tektronix DPO2304SX Printable Help Download | Manualshive

Page: 587 / 920

background image

You can run all tests or specific tests using the options on the Subsystem, Area, and Text drop-down lists. The Diagnostic Status
table lists each diagnostic, the results of the test, and the number of failures that occurred.

Behavior

This window is mainly intended for service personnel. The diagnostic information can be used as part of an incoming inspection
or to diagnose potential problems with the instrument.

NOTE. Remove the input signals before running any diagnostics.

If any diagnostic failures occur, record the failure information, and then contact your local Tektronix service personnel for more
information.

E-mail on event control window

From the Utilities menu, highlight E-mail on Event; then select Setup.

Overview

Use this control window to set up the conditions under which the instrument will send an e-mail, the types of attachments to
include, and the message limits.

Utilities

DPO70000SX, MSO/DPO70000DX, MSO/DPO70000C, DPO7000C, and MSO/DPO5000B Series

555

«
...
585
586
587
588
589
...
»

Summary of Contents for DPO2304SX

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DPO2304SX

Brand: SALUDA MEDICAL Pages: 61

Brand: XanLite Pages: 4

Brand: tayco Pages: 111

Brand: Nectar Pages: 46

Brand: Neauvia Pages: 17

Brand: Pahlen Pages: 20

Brand: Paia Pages: 7

Brand: T&D Pages: 28

Brand: VDO Pages: 15

Brand: VDO Pages: 20

ULTRATHERM 908i

Brand: gbo Pages: 32

Brand: Dantel Pages: 6

Brand: Zero 88 Pages: 22

Brand: Yaasa Pages: 20

Brand: JBL Pages: 17

Brand: GE Pages: 241

Brand: GE Pages: 223

Brand: DAAB Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands