manualshive.com logo in svg

Tektronix DMM830, Manual

Share
Download
Tektronix DMM830 Manual Download Page 40

DMM800 Series Adjustment Procedures

40

Handheld Instruments Basic Service

10.

Disconnect the calibrator from the multimeter.

Perform the following steps to adjust the temperature calibration.

1.

Set the multimeter dial to 

�

C / 

�

F.

2.

Connect the thermocouple adapter ATK01 to the 

�

C V 

�

 

�

 and COM input

connectors of the multimeter.

3.

Set the calibrator to output 18.6

�

 C.

4.

Connect a

 

K-type thermocouple from the calibrator output to the ATK01

thermocouple adapter.

5.

Allow five minutes of settling time for a stable reading.

6.

Adjust VR4 until the display shows 18.5

�

 to 18.7 

�

C.

7.

Turn the calibrator output off.

8.

Disconnect the calibrator from the multimeter.

Perform the following steps to adjust the DC milliamperes calibration.

1.

Set the multimeter dial to mA .

2.

Connect the outputs of the calibrator to the 

�

A mA and COM input connec-

tors of the multimeter.

3.

Set calibrator to output 100.0 mA.

4.

Press and hold the gold button for five seconds. (The multimeter beeps twice

when the gold button is first pressed and then two more beeps follow after

five seconds.)

5.

Press the SETUP button and wait for the calibration to finish (CAL is

displayed during the calibration). After the calibration is completed, press

EXIT SETUP (blue button).

6.

Turn the calibrator output off.

7.

Disconnect the calibrator from the multimeter.

Perform the following steps to adjust the DC amperes calibration.

1.

Set the multimeter dial to A .

2.

Connect the calibrator outputs to the multimeter A and COM inputs.

3.

Set calibrator to output 10.00 A.

Temperature

(DMM850 and DMM870)

DC Milliamperes

DC Amperes

Summary of Contents for DMM830











































Reviews:

No comments

Brands by name

Popular brands

Load more brands