S ection 10 - 2205 S ervice
REPLACEABLE
MECHANICAL PARTS
PARTS ORDERING INFORMATION
Replacement parts are available from or through your lo
cal Tektronix, Inc. Field Office or representative.
Changes to Tektronix instruments are sometimes made
to accommodate improved components as they become
available, and to give you tip benefit of the latest circuit im
provements developed in our engineering department. It is
therefore important, when ordering parts, to include the tal
lowing information In your order. Part number, instrument
type or number, serial number, and modification number if
applicable.
If a part you have ordered has been replaced with a new
or improved part, your local Tektronix, inc. Field Office or
representative will contact you concerning any change in
part number.
Change information, if any, is located at the rear of this
manual.
INDENTATION SYSTEM
This mechanical parts list is indented to indicate item re
lationships. Following is an example of the indentation sys
tem used in the description column.
1 2 3 4 5
N am e & Description
Assem bly and/or Component
Attaching p arts fo r Assembly an d /o r Com ponent
E N D ATTACHING P A R TS
QetaU P art o f Assembly an d /o r Com ponent
Attaching p a rts fo r D etail P art
E N D ATTACHING PA R TS
P arts o f D e tail Part
A ttaching p a rts for P arts o f D ata# P art
E N D ATTACHING P A R T S : \
ITEM NAME
In the Parts List, an item Name is separated from the
description by a coton(:). Because of space limitations, an
Item Name may sometimes appear as inoPmplete. For fur
ther item Name identification, Pie U.S. Federal Cataloging
Handbook H6-1 can be utilized where possible.
FIGURE AND INDEX NUMBERS
Items In this section are referenced by figure and index
numbers to the illustrations.
Attaching Parts always appear in the same indentation
as the item it mounts, while the detail parts are indented to
the right, indented items are part of.and included with, me
next higher Indentation.
AttaPtiitig
parts must
be purchased separately, un
less
otherwise specified.
ABBREVIATIONS
Abbreviations conform to American National Standards
Institute Yl.l
10-1
Summary of Contents for 2205
