manualshive.com logo in svg

Tektronix 071-0060-00, Instruction Manual

Share
Download
Tektronix 071-0060-00 Instruction Manual Download Page 11

Getting Started

2

ORR24 Instruction Manual

The following list highlights the key performance characteristics of the ORR24
Optical Reference Receiver:

H 1000 to 1650 nm wavelength response

H 2.0 GHz Minimum Transducer Bandwidth

H Fourth order Bessel-Thompson, 2.488 Gb/s frequency response

H Greater than 0.5 V/mW DC conversion gain at 1310 and 1550 nm

For a complete list of specifications, see page 10.

Standard Accessories

The following accessories are standard with every ORR24 Optical Reference
Receiver:

H Hard case

H Instructions

H FC/PC to FC/PC 9 mm single-mode fiber jumper

H FC/ST, FC/SC, and FC/FC hybrid connectors

H Coaxial Cable (SMA-to-SMA, 50 W, 2 ns delay)

H SMA terminator

H Certificate of traceable calibration

H Frequency response graph

For a list of replaceable part numbers, see page 19.

Options

The following options are available at the time of purchase:

H Opt 95

Calibration data

H Opt C3

Three years calibration services

H Opt R3

Three years extended warranty

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for 071-0060-00

































Reviews:

No comments

Brands by name

Popular brands

Load more brands