3. Installation Instructions for Built in
-
w
a
.
)
.
The follo ing instructions are directed at the
qu lified installer so that the installation and
maintenance procedures may be followed in
the most professional and expert manner
possible
A the room must be fitted with a ventilation
system which vents smoke and gases from
combustion to the outside
Positioning for gas hob
Important this unit may be installed and used
only in permanently ventilated rooms
The following requirements must be observed
:
:
In a chimney stack or
branched flue
Exclusively for cooking
appliances
.
(
Directly to the outside
2. Product Specifications
B The room must also allow for the influx of
the air needed for proper combustion The
flow of air for combustion purpose must not
be less than 2m
)
.
/
.
h per kw of installed
capacity The supply of said air can be
effected by means of direct influx from the
outside through a duct with a inner cross
section of at least w
100cm
hich must not be
able to accidentally blocked otherwise the room
can be vented indirectly through adjacent rooms
fitted with ventilation ducts to the outside as
described above as long as the adjacent rooms
are not shared areas bed rooms or present the
risk of fire Fig B
C Intensive and prolonged use of the appliance
may necessitate supplemental ventilation
e g opening a window or increasing the power of
the air intake system if present
.
,
,
,
(
. ).
)
,
. .
(
).
3
2
6. How to keep your cooktop in shape
IBefore cleaning or performing maintenance on
your appliance, disconnect it from the electrical
power supply.
To extend the life of the cooktop, it is absolutely
indispensable for it to be cleaned carefully and
thoroughly on a frequent basis keeping in mind
the following
The enamelled parts must be washed with
warm water without using abrasive powders or
corrosive substances which could ruin them
The removable parts of the burners should be
washed frequently with water and soap, making
sure to remove caked-on substances.
On cooktops with automatic ignition, the end of
the ignition device must be cleaned carefully and
frequently, gas holes are not clogged;
Stainless steel can be stained if it remains in
contact with highly calcareous water or
aggressive detergents containing
phosphorous)for an extended period of time. It is
recommended that these parts be rinsed
thoroughly with water and then dried well it is
also a good idea to clean up any spills.
Clean the cooking surface when it is still warm
with a suitable cleaning product. Then rub with a
damp cloth and dry. Aluminum foil plastic items,
objects made of synthetic material, sugar or
foods with a high sugar content that have melted
onto the surface must be removed immediately
with a scraper while the cooking surface is still
hot. Do not use abrasive sponges or cleaning
products under any circumstances. Similar this
holds true for chemically aggressive cleaners
,
:
;
(
,
7. Is there a problem?
It may occur that the cooktop does not function
or does not function properly. Before calling
customer service for assistance, lets see what can
be done. First of all, check to see that there are no
interruptions in the gas and electrical supplies,
and, in particular, that the gas valves for the
mains are open.
The gas holes on the burner are not clogged;
All of the movable parts that make up the
burner are mounted correctly;
There are no draughts around the cooking
surface
You press the knob all the way in;
All of the movable parts that make up the
burner are mounted correctly;
The gas holes are not clogged in the area
corresponding to the safety device.
The gas holes are not clogged.
There are no draughts near the cooking
surface .
The bottom of the cookware is perfectly flat.
The cookware is centered correctly on the
burner or the electric hot plate
The support grids have not been inverted
.
.
The burner does not light or the flame is not
uniform.
The flame does not stay lighted on the model
with the safety device.
The burner does not remain on when set to
“low”.
The cookware is not stable.
Check to make sure that:
Check to make sure that:
Check to make sure that:
Check to make sure that:
.
Fig.A
8.customer service
In case of malfunction of your appliance, you
may eliminate the problem by following
“Is there a problem”. If it persists, please contact
your dealer or nearest authorized service
department by telephone or mail indicating the
following information:
1.Your name, telephone number and
communication address;
2.The model number and serial number of your
machine
3.Description of the fault
;
.
Page7
User Manual
Page2
User Manual
Model Series
Gas Type
Electric Ignitor
Safety Device
Top Glass
GK LUX Series
LPG, 28 mBar
Battery 1.5 V DC *
Thermocouple Sensor
Tempered, 8 mm thickness
Diameter (mm)
Burner Type
Big Burner
Medium Burner
Small Burner
Diameter (nett)
130 mm
95 mm
56 mm
Heating Power
5 KW
2 KW
1.1 KW
* Some Models use 220 Volt AC
