background image

 

16 

TECHNICAL ASSISTANCE AND SPARE PARTS 

 
Before leaving the factory, this appliance will have been tested and regulated by expert 
and specialized personnel in order to guarantee the best performances. 
Any repairs or adjustments which may be subsequently required may only be carried out 
by qualified personnel with the utmost care and attention. 
For this reason, always contact your Dealer or our nearest After Sales Service Center 
whenever repairs or adjustments are required, specifying the type of fault and the model of 
the appliance in your possession. 
Please also note that genuine spare parts are only available from our After Sales Service 
Centers and authorized retail outlets. 
 
The above data is printed on the data label put on the interior part of the appliance and on 
the packing label. 
The above information enables the technical assistant to possibility to get the correct spare 
parts for repairs. We suggest to fill the table below. 
 
 
 
 
MARK: ........................................................................ 
MODEL: ...................................................................... 
SERIES: ...................................................................... 
 
 
 

 

 
 
 
 
 
 
 
 
 
 

 

 
 
 
 
 

Summary of Contents for E/70 5G AI TR

















Reviews: