7
The maximum altitude for installation must be lower than
2.700 m
If the instructions for installation for the gas hob specify a
greater distance, this must be adhered to.
• This appliance is marke
d according to the European
directive 2012/19/EC - UK SI 2013 No.3113 on Waste
Electrical and Electronic Equipment (WEEE).
• By ensuring this product is disposed of correctly, you will
help prevent potential negative consequences for the
environment and human health, which could otherwise be
caused by inappropriate waste handling of this product.
• The symbol
on the product, or on the documents
accompanying the product, indicates that this appliance may
not be treated as household waste. Instead it should be taken
to the appropriate collection point for the recycling of electrical
and electronic equipment. Disposal must be carried out in
accordance with local environmental regulations for waste
disposal.
• For further detailed information regarding the pr
ocess,
collection and recycling of this product, please contact the
appropriate department of your local authorities or the local
department for household waste or the shop where you
purchased this product.
Appliance designed, tested and manufactured according to:
• Safety: EN/IEC 60335
-1; EN/IEC 60335-2-31, EN/IEC
62233.
• Performance: EN/IEC 61591; ISO 5167
-1; ISO 5167-3; ISO
5168; EN/IEC 60704-1; EN/IEC 60704-2-13; EN/IEC 60704-3;
ISO 3741; EN 50564; IEC 62301.
• EMC: EN 55014
-1; CISPR 14-1; EN 55014-2; CISPR 14-2;
EN/IEC 61000-3-2; EN/IEC 61000-3-3. Suggestions for a
correct use in order to reduce the environmental impact:
Switch ON the hood at minimum speed when you start
cooking and kept it running for few minutes after cooking is
finished. Increase the speed only in case of large amount of
smoke and vapor and use boost speed(s) only in extreme
situations. Replace the charcoal filter(s) when necessary to
maintain a good odor reduction efficiency. Clean the grease
filter(s) when necessary to maintain a good grease filter
efficiency. Use the maximum diameter of the ducting system
indicated in this manual to optimize efficiency and minimize
noise.
Use
The hood is designed to be used either for exhausting
or filter version
.
Operation
The hood is fitted with a control panel with aspiration speed
selection control and a light switch to control cooking area
lights.
1. Lights ON/OFF
2. Motor ON/OFF
When key
“2”
is pressed the motor passes to speed 1.
If the key is pressed during working, the hood passes to
OFF
state.
3. Speed decrease
When key
“3”
is pressed the speed decreases from 4
(intense) to 1.
4. Speed increase
When key
“4”
is pressed with the hood in
OFF
state, the
hood passes to speed 1.
If the key is pressed during working, the speed increases
from 1 to 4 (intense).
The int
ense speed is timed. The standard timing is 5’, at
the end of which the hood sets at speed 2.
To deactivate the function before the end of the time,
press key
“3”
, the hood sets at speed 3, when key
“2”
is
pressed the hood turns off.
A signal on the display corresponds to each speed:
OFF: No signal
Speed 1:
1
Speed 2:
2
Speed 3:
3
Speed 4:
4
flashing
5. Display
Grease filter signalling
The grease filter is signalled by the display with number 1
flashing after 40 hours of use.
This means that the grease filter needs to be washed.
The signalling is visible with the hood in
ON
state.
To eliminate the grease filter signalling, press key
“2”
for
more than 3”, until it turns off.
The signalling can be eliminated with the hood in
ON
state.
Carbon filter signalling (only for filtering version)
The carbon filter is signalled by the display with number 2
flashing after 160 hours of use.
This means that the carbon filter installed must be replaced.
The signalling is visible with the hood in
ON
state.
To eliminate the carbon filter signalling, press key
“2”
for
more than
3”, u
ntil it turns off.
The signalling can be eliminated with the hood in
ON
state.
In case both filters are signalled at the same time, numbers 1
and 2 flash on the display alternately.
The signalling can be reset by carrying out the above-
described procedure twice.
Summary of Contents for DOS 60.2 AT
