Teka 10210187, Installation Instructions And Recommendations For Using And Maintaining

Page: 22 / 152

EN
22
HANDLING ELEMENTS (fig. 2)
1 On/Off touch key.
2 Hotplate signaller.
3 Power and/or residual heat di
-
splays*.
4 Hotplate selection touch keys.
5 Decimal point for the clock*.
6 Touch slider key for reducing and
increasing power / time.
7 Clock display.
8 Clock / locking touch key.
9 Decimal point of the power and/or
residual heat displays*.
10 Lock activated indicator*.
11 Lock sign for the remaining touch
keys.
* Only visible while running.
The manoeuvres are done by means
of the touch keys. You do not need to
exert force on the desired touch key,
you only need to touch it with your fin -
gertip to activate the required function.
The touch slider key allows for adju -
sting the power level (1- 9) and se -
lecting the time (1-99) dragging your
finger across it as many times as
necessary until reaching the desired
value. Doing it to the right will increase
the value, whereas to the left it will de -
crease. It is also possible to select the
chosen value by pressing the “+” and
“-” touch keys of the touch slider key.
Each action is verified by a beep. If one
or several touch keys remain pressed
for more than ten seconds, the hob
will automatically switch off for safety
reasons and the beep alarm will go off
as a warning of the possible danger
situation.
SWITCHING ON THE DEVICE
1 Touch the On touch key (1) for at
least one second. The touch control
will become active, a beep will be
heard and the indicators (3) will light
up displaying a “-”. If any cooking
area is hot, the related indicator will
flash an H.
If you do not take any action in the next
10 seconds the touch control will swi -
tch off automatically.
When the touch control is activated,
green-yellow
blue
brown
grey
black
green-yellow
blue
brown
grey
black
green-yellow
blue
brown
grey black
green-yellow
blue
brown
grey
black
green-yellow
blue
brown
grey black
fig. 1
DO
NO
T
USE
L3
Before you connect the stovetop to the
mains, check that the voltage and
frequency match those specified on
the stovetop nameplate, which is
underneath it, and on the Guarantee
Sheet, or if applicable on the techni -
cal data sheet, which you must keep
together with this manual throughout
the product's service life.
Ensure that the inlet cable does not
come into contact with the induction
top housing or the oven housing, if it is
installed in the same unit.
Warning:
The electrical connection
must be properly grounded, fol -
lowing current legislation, otherwi -
se the induction hob may malfun -
ction.
Unusually high power surges
can damage the control system
(like with any electrical appliance).
It is advised to refrain from
using the induction hob during the
pyrolytic cleaning function in the
case of pyrolytic ovens, due to the
high temperature that this type of
device attains.
Apenas o Serviço de assi -
stência técnica oficial da TEKA está
autorizado a manusear ou reparar
o aparelho, incluindo substituir o
cabo de alimentação.
Only the TEKA official techni -
cal service can handle or repair the
appliance, including replacement
of the power cable.
Before disconnecting the hob
form the mains, we recommend
switching off the cut-off switch and
waiting for approximately 25 se -
conds before disconnecting from
the mains. This time is required to
allow for the complete discharge of
the electronic circuitry and thus
preclude the possibility of electric
shock from the cable terminals.
Keep the Guarantee Certi -
ficate or the technical data sheet
together with the instructions
manual throughout the product's
service life. These contain impor -
tant technical information.
Use and Mainte-
nance
User instructions of the
Touch Control